Given the following data for five different materials answer parts A B C D E & F with an explanation 1. Given the following data for five different materialsMaterialYield StrengthTensile Strength(psi)(psi)%ElongationModulus of Elasticity(Ksi)A29000290000.00850700B45000493000.2330457C14500174000.4021750D60190797700.1545000E1015251233000.0930460a. Which of the five materials is more ductile? Why?b. Which material has the lowest stiffness? Why?c. For a given small stress (below the yield strength), which material will have the smaller amountof elastic deformation? Why?d. If the same small stress (below the yield strength) is applied to all materials, which material willexperience the largest plastic deformation? Why?e. Which material has the highest hardness?e. A cylindrical rod 20 inches long, having a diameter of 0.505 inches, is to be subjected to atensile load. The rod may not experience plastic deformation or a change in length of more than0.03 inches when a load of 10050 pounds is applied, which material is a possible candidate?Why?

Given- Mechanical properties of material A, B, C, D and ETo Find-b. Which material has the lowest…

1. Given the following data for five different materials Material Yield Strength Tensile Strength (psi) (psi) % Elongation Modulus of Elasticity (Ksi) A 29000 29000 0.008 50700 གབ་པ་བལ 45000 49300 0.23 30457 14500 17400 0.40 21750 60190 79770 0.15 45000 101525 123300 0.09 30460

1. Given the following data for five different materials Material Yield Strength Tensile Strength (psi) (psi) % Elongation Modulus of Elasticity (Ksi) A 29000 29000 0.008 50700 གབ་པ་བལ 45000 49300 0.23 30457 14500 17400 0.40 21750 60190 79770 0.15 45000 101525 123300 0.09 30460

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: errous metals include which of the following? Question 30 options: Silicon Aluminum Cast…

A: Ferrous metals include which of the following? Question 30 options: Silicon…

Q: 3 l Two tensile samples were cut from a titanium ingot that was cooled very slowly, and under…

A: Tensile material such as titanium with single crystal made from a ingot that is cooled very slowly…

Q: The stress-strain diagram for a metal alloy having an original diameter of 12 mm and a gauge length…

A: Write the given data with suitable variables.

Q: Which choice below describes the mechanical property materials called toughness a ability to…

A: Which choice below describes the mechanical property materials called toughness a ) ability to…

Q: Annealing is a process that can release the residual stress and make the grain size grow larger,…

A: Hardness inversely proportional to squere of grain size so option a was wrong.

Q: Which of the materials depicted in the graph: (Answer with Letter ONLY) Tensile Strength

A: The most ductile material is material C because it's ductility is highest.

Q: means the following this is a non-heat treatable alloy of aluminum and magnesium, that has not been…

A: Yes, it is true.

Q: Which one of the following materials has the highest modulus of elasticity: Group of answer choices…

Q: The shear strength of a metal is commonly determined in which one of the following tests: Group of…

A: The below table describes the determination of corresponding stress for a corresponding test.…

Q: The 2XXX, 6XXX, and 7XXX series of raw aluminum alloy's or non-heat treatable and the 1XXX, 3XXX,…

A: Given: The 2XXX, 6XXX, and 7XXX series of raw aluminum alloy's or non-heat treatable and the 1XXX,…

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: You are a defect analyst, the fracture surface appears relatively smooth to the eye, but under…

A: Option A is correct.

Q: For each question, provide an explanation, identifying the correct choice ( it is marked in red)…

Q: A technician measured the hardness of the steel bar two times. For the first time, he measured the…

A: (a) No, hardness will be changed in both the cases.

Q: Which rivet is least likely to fracture first? a O A b C O B Ос d The rivets are equally likely to…

A: The stress is more predominated by the moment at the point. The moment/torque at a point which is…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: What are the different types of hardness test? Write a detailed note on each type.

A: Hardness is the ability of the material to resist scratch or indentation. Hardness is also defined…

Q: Answer the following questions based on the given information in the table and further calculation…

A: Given Material A Yield strength = 105 MPa Strain = 0.45 Material B…

Q: Several applications are listed below. Determine the relative importance of resilience and toughness…

A: A High tension music wire:- Resilience" Music wire absorb & release energy.,"this processs…

Q: Which of the following statements are true? Creep measures strain as a function of time Creep is…

A: Which of the following statement is true about the creep.

Concept explainers

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.

Question

Given the following data for five different materials answer parts A B C D E & F with an explanation

1. Given the following data for five different materials
Material
Yield Strength
Tensile Strength
(psi)
(psi)
%
Elongation
Modulus of Elasticity
(Ksi)
A
29000
29000
0.008
50700
B
45000
49300
0.23
30457
C
14500
17400
0.40
21750
D
60190
79770
0.15
45000
E
101525
123300
0.09
30460
a. Which of the five materials is more ductile? Why?
b. Which material has the lowest stiffness? Why?
c. For a given small stress (below the yield strength), which material will have the smaller amount
of elastic deformation? Why?
d. If the same small stress (below the yield strength) is applied to all materials, which material will
experience the largest plastic deformation? Why?
e. Which material has the highest hardness?
e. A cylindrical rod 20 inches long, having a diameter of 0.505 inches, is to be subjected to a
tensile load. The rod may not experience plastic deformation or a change in length of more than
0.03 inches when a load of 10050 pounds is applied, which material is a possible candidate?
Why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Expalnation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Properties of Engineering Materials

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The aluminum alloy designated as 5056-H28 means the following: this is a non-heat-treatable alloy of aluminum and magnesium, that has not been modified where 56 represents the specific alloy. The "H2" means that the alloy is strain hardened and partially annealed and the "8" means that the alloy is in full hard condition. True False
Which would be the most likely to measure for an inflated baloon? A. Shear modulus b bulk modulus c young mod If we want to make sure a piece of metal does not easily get bent out of shape, which would be most important to measure for the metal? A. Young b shear c bulk (modulus)
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
What are two differences between clamshell/beach markings and fatigue striations?
The following methods are used to distinguish between ferrous and nonferrous metals and alloys (Choose all that apply) Magnetic test Density test Chemical test Scratching Visual observation Heat treatment
What are three commonly used test to measure the hardness related properties of materials?