a) A 18 V voltage source is applied across a circuit consisting of a 481 ohm resistor in series with a 113 ohm inductive reactance. Calculate the voltage drop across the resistor. (Just enter the magnitude) Answer to two decimal places Enter answer: V

Q: What is the current through the resistor RC, IC, in amperes?  (Enter the number, not the units.

A:

Q: 79. Which of the following formulas can be used with Ohm's law to determine the amount of voltage…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: R= 180 2 120 V 1000 Hz 30 mH coil Solve for total circuit current. Copy paste these in as needed Q°…

A: In this question we will find current in series RL circuit....

Q: XMM6 R13 330n R11 5600 R14 5600 V3 R12 2200 12V

A:

Q: ind the Voltages of all four nodes in the diagram for the following questions.(USE NODAL ANALYSIS)…

A: Nodal analysis, also known as node-voltage analysis, is a method used to analyze electrical circuits…

Q: What is the relationship between the Arc Resistance and the Area of the Cross-Section of

A: Arc resistance depends upon arc length and cross sectional area.

Q: Od. 90.35 ohms QUESTION 8 An inductor has an inductive reactance of 24 ohms, and a resistor…

A:

Q: ext A 4 ate Score 0610908 - Introduction to Electrical Phase 1 1 of 20 What happens to current flow…

A: The resistance is increased, then current will also decreased.  Please follow solution.

Q: R2 560N R1 R3 2200 3300 V1 12V R4 3300 R5 1k0

A:

Q: Ob Oc n the following circuit junctions diagrammed below, which combination of current directions is…

A:

Q: A voltage sources an IR drop across a 20 ohms R1, 60 volts across a 30 ohms R2, and 180 volts across…

A:

Q: When determining Vs why is the 0.91mohm resistor neglected?

A: Need clarity about the calculation of voltage Vs in the given calculation.

Q: What is true re R Plate A Plate B O This circuit used a magnetic field to store electrical charge.…

A:

Q: What is the voltage of the following circuit, if the current and resistance are given? 1A 10

A: According to ohms law voltage across load = Current through resistor ×Value of resistance. Given…

Q: 1202-15° Calculate 11, 12, 13 and 14 40 non +1 1₁ j200 m 6230° 12 13 13 14 -j300 500

A: In this question we need to find the current I1, I2 , I3 & I4.

Q: Vdc0 U=12 V Circuit #1 Ried LED www Ried_series Vdc0 U= 12 V Current in LED (A) Circuit 0.03 #₂ 0.02…

A: Given Data:An LED illumination circuit with,Supply voltage Set-current of the diodes V-I…

Q: R13 3300 R11 5602 R 14 V3 5602 R12 12V 220Ω 10

A:

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.