a) A 10.0 kg crate is resting on a 6.0-meter long horizontal beam with a mass of 5.0 kg and held in place by a wire at a 37-degree angle with respect to the board. Unfortunately, the pivot point is relatively weak, and if the vertical force exceeds 5.0 N, the pivot will break and the board will fall. How close can the crate be moved toward the wall before this happens? What would be the tension in the wire right before this happens?

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Hi, -26.088 or 333.911 is INCORRECT for Ox please recheck

A:

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: Says.003 is wrong

A:

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Help , Handwritten only. No Chatgpt

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: Select the correct statement about the notation circled in green and marked as letter C. Assume all…

A:

Q: G R.75 00.63 THRU E 01.123 F0.250 T 2.00 1.00 1.38 1.123 mm diameter hole with depth of 0.250 mm…

A:

Q: How did you find the value of Patm of value 101.325?

A: How did you find the value of Patm =101.325 kPa?

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: la) Compare the relative load strength of the following two bolts: Bolt 1 = %" Dia x 3" Long and is…

A:

Q: 2? Would it be .4070? Or would it be .4070/.4

A: 2) it would be .4070/.4065

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: Rc is -178.25 Ib. Why in the formula it's 17825 ?

A: The value of RC is represented as : Rc=-178,25 =-17825 lb The negative sign denote the direction…

Q: +0.15 +0.25 The dimensions for the shaft size are Ø30 –0.25 mm and the hole size are Ø30 - 0.15 mm.…

A: Solution:

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: Figure 8m d 1 of 1 Determine the constant angular velocity of the vertical shaft of the amusement…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.