A 76 mm x 76 mm x 6 mm angular section is welded to an 8-mm thick gusset plate as shown. The angular member is A36 steel with Fy= = 248 MPa and Fu = 400 MPa. The electrode used is E60 with Fu = 414 MPa. The cross sectional area of the angle is 929 mm2. L76×76×6 gusset plate 65 mm 125 mm P Compu te the value of P based on the gross area? Determine the value of P based on the net area if the strength reduction coefficient is 0.85? Determine the value of P based on block shear in the gusset plate along the weld?

A 76 mm x 76 mm x 6 mm angular section is welded to an 8-mm thick gusset plate as shown. The angular member is A36 steel with Fy= = 248 MPa and Fu = 400 MPa. The electrode used is E60 with Fu = 414 MPa. The cross sectional area of the angle is 929 mm2. L76×76×6 gusset plate 65 mm 125 mm P Compu te the value of P based on the gross area? Determine the value of P based on the net area if the strength reduction coefficient is 0.85? Determine the value of P based on block shear in the gusset plate along the weld?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

True or FALSE ?? In the analysis of line welds, the variable Ju has dimensions of length cubed.
The axial assembly consists of a solid 1.06-in.-diameter aluminum alloy [E = 9600 ksi, v = 0.31, a = 14.6 x 10-/°F] rod (1) and a solid 1.48-in.-diameter bronze [E = 12200 ksi, v = 0.18, a = 7.2 x 10-6/°F] rod (2). Assume L1=12 in., L2=27 in. If the supports at A and C are rigid and the assembly is stress free at 1°F, determine: (a) the normal stresses o1,02 in both rods at 135°F (positive if tensile, negative if compressive). (b) the displacement ug of flange B (positive if to the right, negative to the left). (c) the change in diameter Ad of the aluminum rod. B (1) (2) L1 L2 Answers: ( a) σι - i ksi, 02 = i ksi (b) ug = i in. (c) Ad, = i in.
3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
Instructions: Please show complete solution. _ Thank you!
7 Enercise:- 30 long with is subjected to a Assuming deformation is entirely elastic and manimum allowable elongation tensile 30000y that the is 0.3 mm while manimum. allowable reduction in, digmeter is 0.015mm. choose amory below only. candidate meeting requirent E (GPa) A cylindrical rod 100 mm diameter of 12 mm load of 30000 N. Aluminium alloy Bronze Titanium allow 70 100 110 U(Poiss ons vahi) 0.33 0.34 0.3
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
Situation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 electrodes. The width of the plate is 50 mm and the thickness is 12 mm. Use Fy = 248 MPa T+ T4 O 29 mm O 30 mm 1. Which of the following nearly gives the diameter of the slot weld using the LRFD method. O 27 mm E70 O 28 mm T T
please answer completely. need asap
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
How to solve this question step by step
need fast