A 600 KVA generator with X"a = 0.22 per unit is connected to a bus through a circuit breaker, as shown in the following figure. Connected through circuit breakers to the same bus are three synchronous motors rated 200 KVA, 2.5 KV, 1.0 power factor, with X"a = 0.15 per unit. The motors are operating at full load, unity power factor and rated voltage, with the load equally divided among the machines. (a) Find the rated symmetrical short-circuit current in Amperes, which must be interrupting breakers A and B for a fault at point P. Simplify the calculations by neglecting the Prefault current.

A 600 KVA generator with X"a = 0.22 per unit is connected to a bus through a circuit breaker, as shown in the following figure. Connected through circuit breakers to the same bus are three synchronous motors rated 200 KVA, 2.5 KV, 1.0 power factor, with X"a = 0.15 per unit. The motors are operating at full load, unity power factor and rated voltage, with the load equally divided among the machines. (a) Find the rated symmetrical short-circuit current in Amperes, which must be interrupting breakers A and B for a fault at point P. Simplify the calculations by neglecting the Prefault current.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 4-pole, d.c. generator has a wave-wound armature with 792 conductors. The flux per pole is [751.3 r.p.m.] 1. 0.0121 Wb. Determine the speed at which it should be run to generate 240 V on no-load. 2. A 20 kW compound generator works on full-load with a terminal voltage of 230 V. The armature, series and shunt field resistances are 0.1, 0.05 and 115 Q2 respectively. Calculate the generated e.m.f. when the generator is connected short-shunt. [243.25 V] (Elect. Engg. Madras Univ. April, 1978) 3. A d.c. generator generates an e.m.f. of 520 V. It has 2,000 armature conductors, flux per pole of 0.013 Wb, speed of 1200 r.p.m. and the armature winding has four parallel paths. Find the number of poles. [4] (Elect. Technology, Aligarh Univ. 1978) When driven at 1000 r.p.m. with a flux per pole of 0.02 Wb, a d.c. generator has an e.m.f. of 200 V. If the speed is increased to 1100 r.p.m. and at the same time the flux per pole is reduced to 0.019 Wb per pole, [209 V] 4. what is then the induced…
A) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the total load resistance. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b" B) Adding resistive loads in parallel to the output terminals of a series connected DC generator will the current through the field winding. a) increase b) decrease c) either "a" or "b" d) neither "a" nor "b"
A 600 KVA generator with X"a = 0.22 per unit is connected to a bus through a circuit breaker, as shown in the following figure. Connected through circuit breakers to the same bus are three synchronous motors rated 200 KVA, 2.5 KV, 1.0 power factor, with X"a = 0.15 per unit. The motors are operating at full load, unity power factor and rated voltage, with the load equally divided among the machines. (a) Find the rated symmetrical short-circuit current in Amperes, which must be interrupting breakers A and B for a fault at point P. Simplify the calculations by neglecting the Prefault current. M. GHA B
A 4 pole generator with wave wound armature has 54 slots each having 28 conductors. The flux per pole is 0.01 Wb. () At what speed must the armature rotate to give an induced EMF of 220V is, (i) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
A 4 pole generator with wave wound armature has 52 slots each having 22 conductors. The flux per pole is 0.01 Wb. (i) At what speed must the armature rotate to give an induced EMF of 220V is, (ii) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed is,
Energy Question-1) Three identical synchronous generators were connected in parallel and the idle frequency values of each generator were set to 54 Hz. The frequency - power characteristic slopes of the first and second generators are 5.3 MW/Hz and the slope of the third generator is 3.9 MW/Hz. When these three identical synchronous generators feed a load together, the system frequency becomes f=51.7 Hz. According to this;a-) Calculate the active power value that the first generator will provide to the load.b-) Find the active power that the second generator will provide to the load.c-) Find the active power that the third generator will provide to the load.d-) Calculate the power of the load.(All values in options a, b, c, and d in this Question will be entered as two digits after the comma.) NOTE: If the information in the text and the photo is different, please solve the question using the information given in the photo. Help me please... Thank you so much.
Three (533 KW, 483, KW, 583 KW) 480 V diesel -driven 60 Hz synchronous generator, A, B and C are in parallel. and taking shares of a 183 KW, 283 KW,333 KW and the speed regulation of the three machines are 2.5% , 2%, and 2.7% respectively. System frequency is 60HZ. If a three phase 400KW resistance load and three phase induction motor draw 533 KVA at .8 pf added to the bus Determine a) The system real power b) The system frequency c) Real power carried by each machine GSR(speed regulation) GSR xf rated A f rated A P
(a) A 4 pole generator with wave wound armature has 65 slots each having 14 conductors. The flux per pole is 20 mWb. At what speed must the armature rotate to give an induced EMF of 225V. (b) What will be the voltage developed, if the winding is lap connected and the armature rotates at the same speed
A 60 MVA, 69.3 KV, three-phase synchronous generator has a synchronous reactance Xs = 15 ohm/phase. The generator is supplying its rated power (i.e. 60 MVA) to an infinite bus at 0.8 power factor lagging. Determine: a) The armature current Ia. b) The generator emf per phase (E). c) The power angle. d) The maximum power (P) that the generator can supply. Xs = j 150 la Vline = 69.3 KV