A 6. A built-up wooden beam is subjected to a vertical shear of 6 kN. It is made 2 ст by gluing together several planks. Determine the average shearing stress at point B. 18 сm B 2 сm 24 cm 2 cm 20 сm 3 cm 3 cm

Q: zain IQ İlı. Saly ibäi The units of length,mass,time-13 are a- Fundamental units. O b-Derived units.…

A:

Q: In what directions do sound waves move?

A: Sound wave propagates as an acoustic wave which have oscillation in pressure, stress, particle…

Q: Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for…

A:

Q: Draw the activities in (A-O-A) way, representing the activities on the arrow, then find the critical…

A:

Q: A truss, as shown in the figure, is carrying 180 kN load at node L,. The force in the diagonal…

A:

Q: Q5. Give the plural noun of the following words. (Choose 5 only) Singular 1.City. 2.brother. 3.man.…

A: Basic concept introduction- Plural noun- It represents more than one entity while a singular noun…

Q: Find Y bar

A: This question is related to Engineering Mechanics. In this question we calculate Centroid along Y…

Q: Given the two orthogonal projections of the object (top view and front view), identify the third…

A: Data given Find the side view

Q: I beleive this is incomplete or I do not understand it at all

A:

Q: x5 – 1024 - find lim x→4 x – 4 O 1100 O 1300 O none O 1280

A: Divide x5-1024 by x-4 ,as x=4 is a solution forx5-1024 Now apply limit for remaining part

Q: What is kinematics? What is meant by pitch, yaw and roll?

A:

Q: 26

A: Mohr-Coulomb Failure Criterion the shear stress of the soil is the failure of the shear stress plane…

Q: he bracket is supported by diameter = 18 mm diameter pins at A and B (the pin at A fits in the 0-35°…

A:

Q: (x+yc )dx - (xc ) dy こ0

A:

Q: completion of one full pattern is called a a. period b. Cycle c. Frame d. Segment

A: Hope you can understand what is mean by frame, frame is like something like reference, every…

Q: 1 2 T - 3 CONCACA NIDO Force diagrams - Inclined plane 5 Performs various tests by modifying the…

A:

Q: This ceiling register has equally spaced openings. a. Find in inches the width of each opening.b.…

A: Total number of opening in a row=9 spacing between the opening in row=38in Total number of opening…

Q: * aut cad Ray is one of the commands for the drawing list. It is used to draw a ray, using two…

A: Explanation :  Ray  command in AutoCAD  is used to draw rays from a starting point in a perticular…

Q: Draw the shear and moment diagrams of the following beams by semi-graphical method. Write the shear…

A: Given: Required  Shear force and bending moment diagram

Q: can u get the

A:

Q: Ali never does his homework. The verb does is full verb. Select one: True False

A: Brief concept- Full Verb- A full verb is a verb that completes the action and does not require a…

Q: The following data are obtained from a liquid limit test. Draw the flow curve and determine LL value…

A: Draw the Flow curve and Liquid Limit value of the soil ?

Q: Is this a three moment equation problem

A: The procedure followed is not three moment equation method.

Q: Differentiate force system based on line of action.

A: A force is a push or pull on an object caused by its interaction with another object.

Q: 50lve the FotHowing diFfere differentiatequation dyメーノーマ 17कय

A: Given datadydx=x-y-2x+y+4dydx=x-y-2x+y+4let us take u=x-y-2and v=x+y+4dydx=uvVdy=udxintegrate both…

Q: what is mercury manometer? own words

A:

Q: For the pipe system shown, find the length of pipe 4 if Q1 = 1m3/s, Q2 = 0.35m3/s and Q7 = 0.27m3/s.…

A:

Q: You are a professor of architecture. Show your students where the horizon line and vanishing points…

A:

Q: 2. FROM THE GIVEN BEAK COMPUTE THE FF. a: REACTIONS @ A 3 B b. SHEAR AND MOMENT AT D 3 C C DRAW HE…

A:

Q: 4 in 2 in 4 in 8 in -12 in- -16 in-

A:

Q: H.W: Replace the 600 Ib force of Figure below by a force through A and a couple whose forces act…

A:

Q: 1. Differentiate atmospheric pressure, gauge pressure and absolute pressure. 2. State the stability…

A: Note- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: A 500 N 2m 120⁰ 3 m 200 N

A:

Q: Replace the force system in the shown figure by an equivalent resultant force and specify its point…

A: In vector addition, the resultant force is the result of combining a system of forces and torques…

Q: 1) Find the coordinates of the centroid, xc and yc. 2) Calculate the second moment of inertia Ix' at…

A: Given data

Q: Draww SED8 B.M.D The 4000N 5M 5 m

A: given beam

Q: CEM I 52.5 N: Define what each word/number/letter is?CEM I: .... 52.5: .... N: .... ....

A: Brief concept- This CEM I 52.5 N is related to the cement and its types and classification. The…

Q: 80 mm -L- В D 60 mm

A:

Q: On Step 3 where do you get the sin(66.80)? reply asap.

A: Required:Explain sin(66.80) in step 3

Q: Question 3 Determine the moment of inertia in Add your answer Question 4 Determine the moment of…

A:

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: y 25 45 55 25 65 80 I 55 165

A: Divide the given area into five parts as shown in part 1 of the question…

Q: What are Frontal Inversions?

A: Inversion is used when metrological inversion of temperature takes place. It is an alteration from…

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb