A 50.0 mL solution of Ca(OH)2 with an unknown concentration was titrated with 0.340 M HNO3. To reach the endpoint, a total of 19.6 mL of HNO3 was required. Given that 0.00666 mol of HNO3 are used in the titration, What quantity in moles of Ca(OH)2 had to be present in the initial reaction?

A 50.0 mL solution of Ca(OH)2 with an unknown concentration was titrated with 0.340 M HNO3. To reach the endpoint, a total of 19.6 mL of HNO3 was required. Given that 0.00666 mol of HNO3 are used in the titration, What quantity in moles of Ca(OH)2 had to be present in the initial reaction?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

If the concentration of Mg2+ ion in seawater is 1.35 x 10³ mg/L, what OH concentration is required to precipitate Mg(OH)2? Ksp (Mg(OH)2) = 5.6 × 10-¹² OH concentration must be greater than M.
You are preparing standard acid and base solutions for the laboratory, using potassium hydrogen phthalate (KHC₈H₄O₄, abbreviated KHP) as the primary standard. KHP (molar mass = 204.22 g/mol) has one acidic hydrogen. You prepared solutions of both NaOH and HCl. It took 22.65 mL of the NaOH solution to titrate (react exactly with) 1.55 g KHP. It then took 32.35 mL of HCl solution to titrate 25.00 mL of the NaOH solution. What is the molarity of the HCl solution?
7B-3. A 15.00 mL sample of an unknown perchloric acid solution is titrated with a 0.687 M barium hydroxide solution. It takes 29.31 mL of the base solution to reach the endpoint. а. Write a balanced chemical equation for the reaction that occurs. b. What is the molarity of the unknown acid solution?
A solution contains 1.17x102 M iron(III) nitrate and 1.22x10 2 M silver acetate. Solid sodium hydroxide is added slowly to this mixture. A. What is the formula of the substance that precipitates first? formula %3D B. What is the concentration of hydroxide ion when this precipitation first begins? [OH]=
You are running an acid-base titration with hydrochloric acid and calcium hydroxide. The calcium hydroxide is your titrant; it has a known concentration of 0.0891 M. You have added 25.0 mL of the hydrochloric acid solution to an Erlenmeyer flask along with 2 drops of phenolphthalein (fee’-nol-thay-leen) indicator. To begin your first trial, you fill a clean 50 mL buret with the calcium hydroxide solution. Your starting volume is 0.25 mL. After the addition of solution from the buret, you see a color change in the flask, and the end point of the reaction is reached. You note the final volume in the buret to be 18.75 mL. You begin again for your second titration trial. You add 24.8 mL of the hydrochloric acid solution to a clean flask along with 2 drops of indicator. You refill the buret to an initial volume of 1.42 mL. When the reaction is complete, you note the final volume in the buret at 16.74 mL. Then you complete a third trial. You add 25.6 mL of hydrochloric acid solution…
A chemistry graduate student is given 250. mL of a 1.50M hydrocyanic acid (HCN) solution. Hydrocyanic acid is a weak acid with K,=4.9 × 10 1º. What mass of NaCN should the student dissolve in the HCN solution to turn it into a buffer with pH = 8.84? You may assume that the volume of the solution doesn't change when the NaCN is dissolved in it. Be sure your answer has a unit symbol, and round it to 2 significant digits. ?
When a strong base is added to a solution of CuSO4, which is pale blue, a precipitate forms and the solution above the precipitate is colorless Part 1 See Periodic Table Include phases in the balanced chemical equations. What is the net chemical equation that describes this reaction? Cu+2(aq)+2OH−(aq)Cu(OH)2(s) Part 2 When ammonia is then added, the precipitate dissolves and the solution turns a deep navy blue. What is the net chemical equation that describes this event?
Use the following balanced chemical equation to answer the below question: 2H&PO4 (aq) +3Mg(OH)2 (aq) 6H2O m + Mg3(PO4)2 (s) The titration of a 14.0 mL sample of H3PO, requires 3.51 mL of 0.400 M Mg(OH)2 to reach the equivalence point. What is the concentration of H3PO,?
2. Using the procedure described in this module, a student determined the percent KHP in an impure sample of KHP. A 3.150-g sample of impure KHP required 41.50 mL of 0.1352M NaOH solution for titration. (a) Calculate the number of moles of NaOH required for the titration. (b) Calculate the number of moles of KHP present in the impure sample of KHP. (c) Calculate the number of grams of KHP present in the impure sample. (d) Calculate the percent of KHP in the impure sample, using Equation 8. Equation 8: percent KHP in the impure sample, % = ( mass of KHP in the sample,g/ mass of sample analyzed, g) (100%)
7. A 10.00-g sample of the ionic compound NaA, where A is the anion of a weak acid, was dissolved in enough water to make 100.0 mL of solution and was then titrated with 0.100 M HCl. After 500.0 mL HCl was added, the pH was 5.00. The experimenter found that 1.00 L of 0.100 M HCl was required to reach the stoichiometric point of the titration. a. What is the molar mass of NaA? b. Calculate the pH of the solution at the stoichiometric point of titration.
A 0.0750 g sample of an unknown weak monoprotic acid (HA) was dissolved in 25.0 mLof water and titrated with an aqueous solution of 0.0125 M Ca(OH)2. The volume of Ca(OH)2 requiredto bring the solution to the equivalence point was 24.5 mL. Calculate the molar mass of the acid.