A 50 V d.c. shunt motor has armature and field resistances of 20 and2 kQ respectively. When running on no- load, the current taken is 0.04 A and the speed is 3000 RPM .The speed when motor is fully loaded and the total current drawn from the supply is 0.3 A is

Q: It is the Insulator used when the Transmission Lines' path need to take a turn on a sharp corner or…

A: Choose the correct option Which insulator is used to change path of transmission line or dead end.…

Q: VExplain parameters that increase fault conductivity?

A:

Q: The concept of the state of a dynamic system refer to a .maximum set of variables The root locus is…

A:

Q: Why is Preventive Maintenance (PM) important?

A:

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: (a) Explain the following picture and its' importance in selection of circuit breakers Extinction of…

A: Electrical power systems require some switchgear that can be controlled with ease and regulate with…

Q: Draw the schematic diagram of a double line to ground fault and basic equipment of a substation.

A: A double line to ground fault is also known as a phase to phase to ground fault, in this type of…

Q: please could give a simplified drawn schematic/diagram to show a how  microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: Short answer. Explain meter loading and why it is important to consider.

A: Meter Loading  Meter loading is generally seen in electrical devices used to measure the voltage and…

Q: ow does an intermediate switch work?

A: The explanation is as follows.

Q: Fill in the blank: In splicing the fiber alignment can be tuned using a visual fault locator.

A: In... Splicing the fibre alignment can be tuned using a visual fault locator.

Q: In what ways can you safeguard your machine against power outages and other calamities?

A:

Q: Which of the following is not an effect of power interruption? Select one: A. Accidents…

A: Solution :Given Topic :Power failure/interruption.Find:=> Here Select option this is not effect…

Q: In what case is it necessary to use time over current relays 51 along with instantaneous relays 50?…

A: Time-over-current relays (51) and instantaneous relays (50) are often used together in power system…

Q: identify and discuss at least 7 safety requirements for switchgear operation and maintenance…

A: We need to identify and discuss at least 7 safety requirements for switchgear operation and…

Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…

A: We are authorized to answer one question at a time, since you have not mentioned question you are…

Q: Draw the symbol of Relay operation (off) Draw the symbol of Relay operation (on)  Draw the symbol…

A: The symbol of the delay relay operation (off) is The symbol of the delay relay operation (on) is

Q: Automatic voltage regulator will have the ability to maintain the a. Nose point - that can be…

A: Automatic voltage regulator is a solid state electronics device used for maintaining generator…

Q: What frequencies found in RTK radios require licensure?

A: As per the code of federal regulations, it holds the complete rules of FCC. The federal regulations…

Q: Q)Write a report about relay and the difference between relay and contactor?

A: consider the given question;

Q: motor driven conveyors. Before entering the bottles are rejected. Draw ladder diagram to achieve…

A: Please find your answer below in step 2

Q: No arc quenching media is required in ___________ .

A: A curve extinguishing medium is a substance, for example, air or transformer oil, utilized in…

Q: Three closed-loop poles of a system are in the Left-Half plane and one in the Right-Half plane means…

A: The given statement is TRUE because any no of poles on the Right Hand Side of s-plane make a system…

Q: - The -------- is the number of times a monitor screen is built or refreshed in one second, measured…

A:

Q: a) Explain how tripping time affect the entire electrical switchgear operation b) in your opinion…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Explain the validity and suitability of the electrical safety components Emergency Stop Switches.…

A: Emergency Stop Switches:- A fail-safe control is an E-stop switch, often known as an emergency stop…

Q: Explain brownout and its difference to blackout

A:

Q: is measured by the voltmeter and the unit is Volt ect one: True False

A:

Q: What is Bus Bar in electrical engineering?

A: Busbars are mostly used in starting or ending points of the substation. It is a metallic strip or…

Q: Give a brief description for under/over voltage time relay.

A:

Q: what is  protective relaying? what is Time & Setting Multiplier ?

A: What is  protective relaying? A protection relays is a switching equipment which detect faults and…

Q: What is the purpose of protective relaying in power systems, and how does it work?

A: purpose of protective relaying in power systems, and how does it work

Q: Write the ST language equivalent of the attached ladder circuit. Stop Start HH Motor HH OverLoad…

A:

Q: What is the single conditioning elements & data transmission elements of washing machine ?

A:

Q: Is there anything particularly noteworthy about a CPLD?

A: To do:We need to mention some noteworthy points about a CPLD.

Q: applications of Automatic Light Fence Circuit Diagram with Alarm

A: Automatic light fence circuit with alarm: The automatic light fence circuit is a sensitive device…