A 50-mm diameter siphon is drawing oil (S.G. = 0.82) from an oil reservoir as shown. If the head lossfrom point 1 to point 2 is 1.50m and from point 2 to point 3 is 2.40m, find the discharge of oil from thesiphon and the oil pressure at point 2.2.00 m50-mm-diameter siphonOil (s.g. =0.82)5.00 m

Answered: Image /qna-images/answer/13e4457e-c7c7-4432-96f3-02af3bc925d6.jpg

Answered: A 50-mm diameter siphon is drawing oil…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. A siphon draws oil (sg=0.86) as shown in the figure. Determine the volume flow rate of oil from the tank, m3/s. * 3.0 m Oil (sg = 0.86) 10.0 m 50-mm - inside diameter 25-mm diameter
No Handwriting please
= Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asur f 5.6 m². At the bottom of the tank there is a door inclined at an angle = 25 degrees with respect to the horizontal. The door has a length L = 1.1 m and a width w=1 m (out of the page). The flowrate into the tank is Q₁ (t) flowrate out is Qo(t) = 0.05 m³/s At time t = Asurf = 0.26 m³/s and the 0, the water has a depth ho = 2.5 m. The density of water is p = 1000 kg/m³. Ө h(t) Qout
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and is into the reservoir) Assume ha = 10 m, hg = 50 m, hc = 0 m, l₁ = 300 m, l₂ = 250 m, and 3 = 500 m. QA = QB Qc= i Elevation = h VA D₂=0.08 m = = 0.020 Elevation = h у в D,= 0.10 m f = 0.015 < D₂ = 0.08 m f = 0.020 Elevation = h с
Please give a detailed Handwritten solution.
8. In the figure below a manometer uses oil with specific gravity of 0.8. (a) Calculate the discharge when R = 1 ft. (b) Repeat the problem if the pipe is inclined at 30° upward. oil R 6" 3" -- 6"
Give detailed solution,Only Handwritten.
Water 2. In this system, d = 6 in., D = 6 ft, and =z2 = 12 ft. The water in the system is 13 cfs. machine a pump or a turbine? pressures at points A and B? losses. Pump 1. The discharge in the siphon is 2.80 cfs, D = 10 in., L1 = 3 ft, and L2 = 3 ft. Determine the head loss between the reservoir surface and point C. Determine the pressure at point B if three-quarters of the head loss (as found above) occurs between the reservoir surface and point B. 1 m REVIEW Home Work (1) Energy Equation Water T = 10ºC REPPER Water Same elevation Machine Elevation = 40 m -Elevation = 20 m Elevation 10 m 300 m + -300 m- 4. Assume that the head loss in the pipe is given by hL = 0.014(L/D)(V2/2g), where L is the length of pipe and AZ₂ AFL B Elevation 100 m L = 100 m D = 60 cm Water T= 10°C 3. A water discharge of 10 m3/s is to flow through this horizontal pipe, which is 1 m in diameter. If the head loss is given as 7V2/2g (V is velocity in the pipe), how much power will have to be supplied to the flow…
Question 8 download image D The water in a large tank exits through a horizontal circular pipe of diameter D=0.01m and length L=94m. The centre of the exit of the pipe is h=1.0m below the water surface. We can assume that the flow entrance to the pipe is smooth so that there are no minor losses. The flow in the pipe is laminar, the friction factor can be assumed constant and can be found from h fD=64/Rep where the Reynolds number is based on the pipe diameter and mean flow speed in the pipe. Taking frictional losses into account, solve the resulting quadratic equation to calculate the speed of the flow out of the pipe. Give your answer in m/s to 2 decimal places. Use: kinematic viscosity given by v=0.00000114 m²/s density of water given by 1000 kg/m3 acceleration due to gravity of 9.81 m/s² A Moving to another question will save this response. >>
5. What is the minimum diameter at section (1) in the pipe below to avoid cavitation at that location? Take D₂= 15 cm. Neglect friction head loss in the pipe. Water 5 m (1) (2)

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS