A 5.69 kg block located on a horizontal floor is pulled by a cord that exerts a force F = 10 N at an angle 0 = 20.3° above the horizontal, as shown in the Figure. The coefficient of kinetic friction between the block and the floor is 0.03. What is the normal force between the block and the floor? Submit Answer Tries 0/5 What is the acceleration of the block? Submit Answer Tries 0/5 What is the speed of the block 2.6 s after It starts moving? Submit Answor Tries 0/5 ASend Feedback A Post Discussion

A 5.69 kg block located on a horizontal floor is pulled by a cord that exerts a force F = 10 N at an angle 0 = 20.3° above the horizontal, as shown in the Figure. The coefficient of kinetic friction between the block and the floor is 0.03. What is the normal force between the block and the floor? Submit Answer Tries 0/5 What is the acceleration of the block? Submit Answer Tries 0/5 What is the speed of the block 2.6 s after It starts moving? Submit Answor Tries 0/5 ASend Feedback A Post Discussion

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A 1,480-N crate is being pushed across a level floor at a constant speed by a force of 350 N at an angle of 20.0° below the horizontal, as shown in the figure a below. F 20.0° / 20.0° a b (a) What is the coefficient of kinetic friction between the crate and the floor? (Enter your answer to at least three decimal places.) (b) If the 350-N force is instead pulling the block at an angle of 20.0° above the horizontal, as shown in the figure b, what will be the acceleration of the crate? Assume that the coefficient of friction is the same as that found in part (a). m/s²
Now the block on the table has friction. Calculate the frictional force if the block is stationary. m = 8 kg M = 2.8 kg μs = 0.5 μk = 0.4
A 1,500-N crate is being pushed across a level floor at a constant speed by a force F of 370 N at an angle of 20.0° below the horizontal, as shown in the figure a below. F 20.0° / b 20.0° (a) What is the coefficient of kinetic friction between the crate and the floor? (Enter your answer to at least three decimal places.) 0.220 X Your response is within 10% of the correct value. This may be due to roundoff error, or you could have a mistake in your calculation. Carry out all intermediate results to at least four-digit accuracy to minimize roundoff error.
During a physics inquiry, you place a 0.250kg dynamics cart on a ramp inclined at 25.0 degrees to the horizontal. The cart is initially at rest, before you pull it up the ramp with a force sensor. The force sensor exerts a force on the cart parallel to the ramp. The coefficient of friction is 0.300. Determine the force to pull the cart up the ramp at an acceleration of 1.50 m/s/s. Include a force diagram.
A 40 N box is resting on a table when a 20 N force is applied to it horizontally. The coefficients of static and kinetic friction are 0.3 and 0.1, respectively. Which of the following best describes the resulting motion of the box? The motion of the box cannot be determined with the given information. The box accelerates in the direction of the applied force. The box remains at rest. The box moves with a constant velocity in the direction of the applied force.
An object with a mass of 4kg lies on a rough plane inclined at 20 degrees to horizontal. A force of 35N is applied parallel and up the plane. The object accelerates at 2.5m/s^2. What is the Uk between the object and plane
A rancor pulls a 89.6 kg box at a constant speed across the floor. He applies a 328.2 N force at an angle of 34.3° above the horizontal. What is the coefficient of kinetic friction? Use g=9.8m/s
In the situation below, m1=20 kg and m2=10 kg. The masses are at rest. A) What is the minimum coefficient of friction between the incline and m1? B) The sting and cut and m1 slides down the incline. What is its speed when it reaches the bottom? The block is initially at height of 10 meters.
Wnet = m(v₁)² = m(v₁)², Wnet = Σ₁ W₁, W = Fd cos 0 Problem 1: A 2.0 kg box slides on a floor. A friction force of 5.0 N opposes the motion. If the box starts with a speed of 5.5 m/sec, how far does is slide before coming to rest? Answer: d = 6.1 m Problem 2: What is the force a 60.0 kg sprinter exerts backward on the track to accelerate from 2.00 m/sec to 8.00 m/sec in a distance of 25.0 m, if they encounter a wind that exerts an average force of 30.0 N against them? Hint: Wnet = Wrunner - Wwind. Answer: Frunner: = 102.0 N Problem 3: A 500-kg dragster accelerates from rest to a final speed of 110 m/sec in 400 m (about a quarter of a mile) and encounters an average frictional force of 1200 N. What is the work done by the dragster? Hint: Wnet = Wdragster - Wfriction. Answer: Wdragster = 3.5 × 106 J