A 5.00×10−4 M solution of analyte is placed in a sample cell that has a pathlength of 1.00 cm. At a wavelength of 490 nm, the solution’s absorbance is 0.338. What is the analyte’s molar absorptivity at this wavelength?

Q: What is the concentration of a solution with an absorbance of 0.23 a.u. in ppm when y=45.3509y

A: In absorbance (y) versus dilution factor (x) curve, the slope of the curve gives the value for molar…

Q: Suppose that a solution has an absorbance of 0.226 at a wavelength of 450 nm.  If the concentration…

A: Given the absorbance of the solution, A = 0.226 Concentration of the solution, C = 24 μM  path…

Q: The molar absorptivity of a compound at 500 nm wavelength is 252 M-1cm-1. Suppose one prepares a…

A: 1.)  We would use formula of Absorbance.        Note : As you have uploaded two questions, I'll…

Q: x10-5 M analyte with an absorbance reading of 0.003 at 517 nm wavelength?

A: The molar absorptivity (at 1 cm cuvette): E=\frac{A}{C}E=CA​ C = concentration A= absorbance

Q: A mixture is prepared by combining 10.72 mL of 2.52 x 10-3 M Fe(NO3)3 with 10.00 mL of 1.76 x 10-3 M…

A: Given that: Initial concentration of Fe(NO3)3 is 2.52 x 10-3 M. Volume of Fe(NO3)3 solution is 10.72…

Q: Explain why a dispersion of silver nanoparticles coated with an amine functionalised polymer would…

A: Given, dispersion of silver nanoparticles coated with an amine-functionalized polymer would be more…

Q: an absorbance of a solution with a pathlength of 1.00 cm is 0.544 and concentration is 1.40x10^ ^ -3…

A:

Q: Fe+3 (aq) + SCN – (aq) FeSCN +2 (aq)   She mixes 4.00 mL of 2.00 mM SCN– and 5.00 mL of 2.00 mM Fe+3…

A: Given: ℓ = 1.0 cm ε =2867 M

Q: A plot of Absorbance vs. molarity of Fe(SCN)2+ from part one of the lab gives a straight line with…

A: The equation of calibration curve line is given as, => y = 51 x Given : Absorbance of sample =…

Q: A colored solution of concentration 0.0248 mol/L has an absorbance of 0.353. What is the…

A: The Beer-Lambert’s law, the absorbance (A) is directly proportional to the concentration (c) of the…

Q: The absorption coefficient of O2 in seawater at 0°C is 1.7 mmol/L.What is the concentration of O2 if…

A: Given information,        The absorption coefficient of O2 in seawater at 0°C is 1.7 mmol/L.

Q: 2. Calculate the minimum concentration (µg/ml) of bismuth(III) (M=208.98 g/mol) in the analyte,…

A: According to the Lambert Beer's law, the absorbance of the solution is directly proportional to the…

Q: (3) Compound with10^3 x 6.74 molar absorption What concentration of the compound is required to form…

A:

Q: An unknown chemical has an absorbance of 0.265 in a 1.0cm cuvette at a concentration of 0.703 M.…

A: From given data A = 0.265  l = 1 cm c = 0.703 M   Formula used A= ԑcl Where, ԑ is absorptivity…

Q: Estimate the Ka of a weak acid from the data given below. One gram quantities of the acid were…

A:

Q: For this experiment I prepared two solutions: each was an injection of 15 microliters of pure acetic…

A: 1 μL = 10-6 L 1 L = 1000 mL Volume of acetic anhydride (MW = 102.09 g/mol) taken in mL, V = 15.9 μL…

Q: I would need help finding the conductance values for these ions: (Please explain) Ion / compound…

A: Conductance is the ability of a substance to conduct electricity, and it depends on the number of…

Q: An unknown concentration of [FeSal]+ gave an absorbance reading of 0.301. Calculate the…

A: Given:For the unknown solution:Absorbance = 0.301Slope is 1280 and y-intercept is -0.00821

Q: Why 275 nm wavelength is used for the detection of the analyte? Reader should be able to follow your…

A:

Q: The nitrite in a series of standard solutions (mg/L, n = 5) are converted to azo dye and the slope…

A: Creating a standard curve is essential for accurately determining the concentration of an unknown…

Q: To determine copper in a metallic alloy, 1.245 g of an alloy sample is dissolved in a 1: 2 mixture…

A: The molar absorptivity is determined by substituting 0.505 for A, 750 ppm for c, 1cm for l in…

Q: At 21 °C, a solution of 12 mL each of 0.00200 M Fe3+ and 0.001000 M SCN- was mixed and brought to…

A: The given reaction is: Fe3+(aq) + SCN-(aq) → Fe(SCN)2+(aq) Here the product, Fe(SCN)2+(aq) is…

Q: A 131.7 mg sample of powdered Carbamazepine tablets was boiled with ethanol, filtered and then made…

A: Step :

Q: Compound with 103 x 6.74 molar (3) absorption What concentration of the compound is required to form…

A:

Q: Water from Jordan Lake was analyzed for its Fe³+ content. A 20.0-mL sample of lake water was…

A: First, we have to calculate the value of the molar absorptivity constant, ε using the concentration…

Q: A spectrophotometer was calibrated with a 7.236 x 10-4 M (in Cu) Cu-neocuproine solution. This…

A: The question is based on the concept of photochemistry. We need to calculate concentration of…

Q: The absorbance of an unknown dye solution is measured to be 0.47 by a spectrometer. The linear…

A: The given expression for the linear equation for the spectrometr calibration is ; Y = 2156.5 X +…

Q: 4 Determine the time in seconds required to sputter 50 nm of Si using a 10 µA/cm2 beam of 45 keV…

A: Sputtering is a PVD process in which a glow plasma discharge (usually localized around the target by…

Q: Calculate the absorbance of 0.00038 moles in 24.2 mL of solution given the molar absortivity is 1168…

A:

Q: A solution in part C initially contains (4.1000x10^-4) molar SCN¯ and (1.180x10^-1) molar Fe3+. This…

A: Given that: absorbance = 5.150×10-1  initial concentration of Fe3+ = 1.180×10-1 M initial…

Q: The measured absorbance of a solution with a pathlength of 1.00 cm is 0.544. If the concentration is…

A: pathlength (l) =1.00 cm Absorbance (A) = 0.544 concentration(c) = 1.40 x 10 —3M

Q: The molar absorptivity constant of a particular chemical is 2.31 M/cm. Determine the concentration…

A:

Q: Average absorbance, Molarity of Fe(NO₂)), 0.2M Volume of Fe(NO₂)) = 5.00mL Moles of FeMolarityx…

A: The balanced equation for the equilibrium reaction is: Fe3+(aq) + SCN-(aq) ⇌ Fe(SCN)2+(aq) ; K = ??…

Q: Describe step-by-step procedure how you would use atomic absorption to measure copper in urine?

A:

Q: The standard curve was made by spectrophotographic analysis of equilibrated iron(III) thiocyanate…

A: Here  we are required to find the Fe3+ concentration of the unknown solution.

Q: A solution in part B initially contains (4.0800x10^-4) molar SCN" and (2.850x10^-3) molar Fe3+ This…

A: Given that: absorbance = 4.810×10-1  initial concentration of Fe3+ = 4.0800×10-4 M initial…

Q: .0 mL of an unknown FeCl3 solution is diluted to a total volume of 230.0 mL. The diluted  FeCl3…

A: Given that: Initial volume of FeCl3 = 45.0 mLFinal volume of FeCl3 = 230.0 mLAbsorbance = 0.223Molar…

Q: The molar absorptivity of a compound at 500 nm wavelength is 252 M-1cm-1. Suppose one prepares a…

A: Given :- Wavelength =500nm              Molar Absorptinity = 252 M-1cm-1              Moles of…

Q: The observed intensity of light (I) after passing through the sample cell is 0.176 of the initial…

A:

Q: Determine the time in seconds required to sputter 50 nm of Si using a 10 µA/cm2 beam of 45 keV ions…

A: The aim of this question is to explain the 50 nm Si sputtering using 10 µA/cm² 45 keV Ne, Kr and Xe…

Q: A solution in part C initially contains (4.0300x10^-4) molar SCN¯ and (2.880x10^-3) molar Fe3+. This…

A: We have to calculate the equilibrium constant.

Q: Tonic water (20.0 mL) was added into each of two volumetric flasks (100 mL). The first flask was…

A:

Q: Chosen wavelength : 400 nm EDTA Volume (mL) Absorbance O mL 0.445 1 mL 0.439 2 ml 0.434 3 ml 0.428 4…

A: Answer

Spectroanalytical Methods

Spectroanalytical methods measure the wavelength and intensity of radiations that are either emitted or absorbed by a molecular or atomic species. These methods are useful for evaluating the electronic or atomic arrangement of the molecules of a given analyte.