A 5 kg block is attached to a spring of constant k = 2400 N/m. The coefficient of friction between the block and the ground is 0.4. Under its initial condition, a force F is applied to the block until the restoring force of the spring reaches 100 N. To reach its final condition, the applied force F is removed. Then, the block moves and the spring returns to its unstretched position. Use 9.81m/s^2 for the gravity. Fspring = 100N k=2400 N/m 5 kg F If the total work done on the system is 1.2658 J, determine the final velocity of the block (by relating work and kinetic energy). Write only the numerical value without the unit. Do not include the sign. Use up to 4 decimal placer

A 5 kg block is attached to a spring of constant k = 2400 N/m. The coefficient of friction between the block and the ground is 0.4. Under its initial condition, a force F is applied to the block until the restoring force of the spring reaches 100 N. To reach its final condition, the applied force F is removed. Then, the block moves and the spring returns to its unstretched position. Use 9.81m/s^2 for the gravity. Fspring = 100N k=2400 N/m 5 kg F If the total work done on the system is 1.2658 J, determine the final velocity of the block (by relating work and kinetic energy). Write only the numerical value without the unit. Do not include the sign. Use up to 4 decimal placer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There is a spring-mass system, driven by an external piston, which applies a force to it. Newtons that satisfies the following relation F = 6*cos (3*π*t), as can be seen in the figure, it is known that the spring constant has a value of k = 25 Nm, and the block has a mass of 4 kg, furthermore, dissipative frictional effects cause the relationship between velocity and force to satisfy the ratio F = bv, where b is the damping constant, and it is known that the numerical ratio of force is 10 times the value of speed. Determine: a) The natural frequency of the system. b) The driving frequency of the external force. c) The maximum value exerted by the external force. d) The damping constant. e) The amplitude of the forced oscillatory motion in steady state. f) If dissipative (damping) effects are neglected, what is the value of the amplitude.
Asap please
NEED WITHIN 1HR PLEASE, THANKS 1. A 1200-kg automobile is moving at a speed of 90 km/h when the brakes are fully applied, causing all four wheels to skid. Determine the time required to stop the automobile on dry pavement (μk = 0.75), and on an icy road (μk = 0.10).
A 2-kg block travels from the top of a plane inclined 25° with the horizontal compressing a spring at the bottom of the incline with an initial speed of 0.65 m/s. Due to the motion of the block, the spring was compressed by 0.2 meters. The spring has ak of 100 N/m and the coefficient of friction between the block and the incline is 0.40. What is the change in Elastic Potential Energy of the block? O 9.5) O 2.0) O 8.8) O 1.1)
A horizontal force of 300 lbs pushes a 200lb block up an incline whose slope is 3 vertical to horizontal. If the coefficient of friction is 0.2 determine the time required to increase the velocity of the block from 10 to 50 feet per second.
A simple pendulum consists of a 0.8- kg bob connected to a massless inextensible cord with a length L = 1.9 m. The bob is set into motion and its angular displacement is given by e(t) = 0.11cos(wt), where e is in radians and t is in seconds. Take g = 9.8 m/s^2, determine the mechanical energy of this pendulum.
Given a system of pulley below. Block A has a mass of 50 kg. At point P it is recorded to have a velocity equal to 12 m/s with on increasing acceleration of 6.5 m/s^2. Determine the power input to Motor at M at this instant if its efficiency is given to be 0.80.
4
Consider the mass-on-a-spring system as shown in the figure below. The spring has a spring constant of 1.86e+3 N/m, and the block has a mass of 1.39 kg. There is a constant force of kinetic friction between the mass and the floor of 4.71 N. Starting with the spring compressed by 0.117 m from its equilibrium position, how far will the block travel once it leaves the spring? (Assume that block leaves the spring at the spring's equilibrium position, marked x=0 in the figure. Give your answer as the distance from the equilibrium position to the final position of the block.) Hint: How much work must friction do in order to bring the mass to a stop? How much distance is required for friction to do this work? Enter answer here www.m X = 0 Please enter a numerical answer below. Accepted formats are numbers or "e" based scientific notation e.g. 0.23, -2, 1e6, 5.23e-8 Image size: S M L Max m
#7) You use a rope to apply a horizontal force of 63 N to pull a box a distance 7 m across the floor at constant velocity in 5 secons, and a frictional force of opposes this motion. What is the power dissipated as heat by the frictional force? F = 63 N fr X1 = 7 m
A simple pendulum consists of a 0.8-kg bob connected to a massless inextensible cord with a length L = 1.1 m. The bob is set into motion and its angular displacement is given by e(t) = 0.11cos(wt), where e is in radians and t is in seconds. Take g = 9.8 m/s^2, determine the mechanical energy of this pendulum.
แสดงวิธีทำให้ดูหน่อยครับ