A 4-m-long steel rod must not stretch more than 3 mm and the normal stress must not exceed 150 MPa when the rod is subjected to a 10-kN axial load. Knowing that E5 200 GPa, determine the required diam-eter of the rod

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

A:

Q: 3. A column is made of concrete having a density of 3000 Kg/m³. At its top B it is subjected to an…

A: Given Data:The density of the material is The load applied to the column is P = 25 kN.The radius of…

Q: (a) A steel cylinder of 60 mm inner radius and 80 mm outer radius is subjected to an internal…

A: Note: As per the bartleby guidelines only three subpart will be solved at a time for remaining…

Q: A tensile stress is to be applied along the axis of a cylindrical brass rod that has a diameter of…

A: given; diameter (d)=10mmchange in diameter (δd)=2.5*10-3mmelasticity(E)=10.1*104MPapoisson's…

Q: For the clevis connection shown, the shear stress in the 0.21-in.-diameter bolt must be limited to…

A: Given: Let us consider the given data, Shear stress,  τ=39 ksi=39×103 Psi Bolt's diameter, d=0.21 in…

Q: Two steel plates are to be held together by means of 16-mm-diameter high-strength steel bolts…

A: Given, Pb = 200 MPa. Ps=130 MPa db=16 mm The diagram shows that the nut and bolts are applying a…

Q: 5-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the…

A: Given:P=5 kNL=50 mE=200 GPaσn=150 MPa∆L=25 mm

Q: Rods AC and BC are used to suspend the 205 kg mass. A 60° -60° B C If each rod is made of a material…

A: dac = dbc = 5mmExplanation:

Q: 1.3 Two solid cylindrical rods AB and BC are welded together at B and = loaded as shown. Knowing…

A: Given P = 10 kips To find Average normal stress

Q: Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a…

A:

Q: Link BC is to be made of a steel for which the ultimate normal stress is 250 MPa. Determine the…

A:

Q: A 500 kg mass is supported by steel cables A and B, as shown below. Determine the minimum diameters…

A: In this problem, we will determine the minimal diameter of the cable by first calculating the force…

Q: Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a…

A:

Q: An 18-m-long steel wire of 5-mm diameter is to be used in the manu-facture of a prestressed concrete…

A: Given is: Length of steel wire, l=18m Diameter of the wire, d= 5mm = 0.005m Stretch or change in the…

Q: The rigid bar ABD is connected to the rod BD which consists of a single bar with a width of 25,0 mm…

A:

Q: A 12-kN tensile load will be applied to a 50-m length of steel wire with E= 200 GPa. Determine the…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.