A 40µF, 600V paper capacitor is available but we need one having rating of about 300µF. It is proposed to use a transformer to modify the 40µF so that it appears as 300µF. The following transformer ratios are available: 120V/330V; 60V/450V; 480V/150V. Which transformer is the most appropriate and what is the reflected value of the 40µF capacitance? To which side of the transformer should the 40µF capacitor be connected?

A 40µF, 600V paper capacitor is available but we need one having rating of about 300µF. It is proposed to use a transformer to modify the 40µF so that it appears as 300µF. The following transformer ratios are available: 120V/330V; 60V/450V; 480V/150V. Which transformer is the most appropriate and what is the reflected value of the 40µF capacitance? To which side of the transformer should the 40µF capacitor be connected?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A voltage multiplier has 12 stages Capacitances, all equal to 0.08 μF. Thesupply transformer secondary voltage is 150 kV at a frequency of 100 Hz. Load current 0,006A.What is the percentage ripple, the regulation and the optimum number of stages for minimumregulation or voltage drop.
q9
Figure 2 shows three "LC" circuits, two of them with capacitance capacitors "C" and the three with inductance coils "L", the three circuits are coupled by means of two capacitance capacitors "Cc". The currents that circulate through each mesh are those indicated in the figure: "I1", "I2" and "I3". Using Kirchhoff's law for voltages and taking into account the definition of current I = −dQ / dt, find the system of coupled equations of the system and then find the normal angular frequencies of the system.
For all questions in this page, assume that the transformer is ideal. One side of a transformer has 280 turns while the other side has 140 turns. The high voltage side is connected to a 120 Vrms source. The low voltage side (secondary) is connected to an impedance Z₁ = 11.7 + j6.8 0. provide at least 2 digits after the What is the value of the load impedance when referred to the primary? Referred impedance = Q
Tansformers
A 12V rms ac supply is connected to the primary winding of a transformer with a turns ratio of 0.052. calculate the RMS secondary voltage given a voltage regulation of 4.0%.
Please answer in typing format please ASAP for the Thanks in advance Please all subpart is compulsory
The zener regulator 5.6 V DC is interfaced with 6.4 V DC relay. How many voltages should be provided by the DC power supply as shown in given Figure?
A 5 to 1 ratio, step-down 10 transformer has 230/460 V secondary voltages. The secondary winding being continuously wound but with the center tap brought out. Across one half of the winding is connected an induction motor drawing 50 A at 0.72 pf and 230 V. On the other half is connected an over-excited synchronous motor drawing 40 A at 0.9 pf and 230 V. (a) Determine the current thru the center tap (b) Assuming no-loss, determine the real power at the primary side 3.
A 200-kVA, 230-V/230-kV testing transformer having a resistance and leakage reactance of 2% and 7% respectively, is to be used as a resonant transformer at 50 Hz to test a piece of cable at 400 kV. The load capacitance is 0.01μF and inductor coil is assumed to 3% resistance. Determine the series inductance required and the input voltage. ..
1)The value of the capacitance reactive power in VAR is? /2) The value of the capacitor in micro farad is?
IV- Transformer Design You are requested to design a transformer which will have the following characteristics: Two windings, one primary and one secondary with an E-shape core. Vin = 220 V RMS 16 s Vout < 20 v RMS open circuits 14.5 V < Vout s 16 V on a 100 N resistor. 2 VA < S 35 VA apparent power. Show all steps of your design with calculation. - Indicate current in primary and secondary in both open circuit and with 100 n resistor. Simulate your transformer and show both input and output voltage with the 100 Ω load. Talk about your transformer and wire sizes.