Answered: A 4,000 pound car travels at 30 miles…

A 4,000 pound car travels at 30 miles per hour on a circular path of radius 100. feet. In order to prevent slipping. What frictional force must it exert? on the road?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.4P: A compact car travels 30 mi on one gallon of gas. Determine the gas mileage of the car in km/L. Note...

See similar textbooks

Related questions

Q: Convert 5 acre · ft to gallons. 1629020.1945o gallons

A: Given data 5 acre.ft to gallons

Q: Q1. A conservative force is a force that the work done by it only depends on its initial and final…

A: Conservative force is the force due to which work done arise depends on initial and final positions…

Q: 1. Intravenous infusions usually are driven by gravity by hanging the fluid bottle at a certain…

A: The gauge pressure of a fluid is the measurement of pressure relative to the atmosphere. It is…

Q: Suppose that a $100 lump sum amount is invested for 10 years at a nominal interest rate of 6%…

A: given; principal amount(P)=$100time(T)=10yearinterest rate(R)=6%amount at the end of 10year (A)=?

Q: Can you please do 5.67. Thx

A: Draw the free body diagram.

Q: tan & = 8 - 缶 tan 3.

Q: heat pump with the COP of 3.8 supplies heat at the rate of 289 kJ/min. If a bar heater was used and…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A 4,000 pound car travels at 30 miles per
hour on a circular path of radius 100. feet. In
order to prevent slipping. What frictional
force must it exert? on the road?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plane moves at 820km/h as it makes a horizontal circular turn of radius 15.0 km. a. Draw a free body diagram and show all the forces on the pilot man who is inside the plane. b. Figure out the magnitude of the net force on the 78.0kg pilot. 10000
A compact car travels 30 mi on one gallon of gas. Determine the gas mileage of the car in km/L. Note that 1gal=3.785L.
A magnetic particle weighing 3.6 grams is pulled through a solenoid with an acceleration of 6m/s². Compute the force in pounds acting on the particle.
I need help on this question
Question 2 The wheel A and a block B are connected by a cable. The coefficient of friction of the wheel and the ground is HA = 0.4. The coefficient of friction of the block and the ground is HB = 0.3. The wheel A has mass 40 kg, and the block B has mass 30 kg, with a %3D center of gravity shown. The radius r, = 0.5m. The outer radius is 1 m. a) Determine the smallest force P (applied vertically) that will cause motion to impend. b) What type of motion is impending? (i.e. slipping/tipping at A/B)
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel? a. none b. 48.803m c. 40.078m d. 47.800m 3. 40.780m
Please do it asap
As speed as possible please
While winching a Jeep straight out of the mud, a winch uses 4800Watts of electrical power to pull the 1500-kg Jeep 12meters as it accelerates at 0.15. This takes a the winch 20 seconds to accomplish. Calculate... a.) the force of tension in the cable for the winch to pull the jeep. b.) the work done by the winch to pull the jeep. c.) the power done by the winch to pull the jeep. d.) the efficiency of the winch in this scenario.
An arborist is cutting down a tree a 28 m high tree bystarting his cut 1.8 m above the ground. The tree has a mass of 3750 kg. The tree trunk can be thought of as a uniformly dense, thin rod. 1. What's the speed of the tree’s center of mass when the trunk is parallel to the ground on its way down. The tree rotates about the point where it is cut., 1.8 m above the ground. 2. What is the total amount of kinetic energy that the tree has at thatpoint of parallelism to the ground? How fast would a 950.0 kg truck have to be traveling to have the same kinetic energy as the tree?
a.) What is the angle, measured relative to the positive x-axis, of the load's acceleration? (The correct answer is: -10.219 degrees) Just need the steps to get there b.) Three horses pull and guide a 132 kg payload down a river, exerting the forces shown in the figure, with F1 = 29 N, F2 = 38 N, F3 = 58 N, θ1 = 30°, and θ2 = 60°. What is the magnitude of the payload's acceleration? (The correct answer is: 0.7861 m/s^2)Just need the correct steps to get there
A block is being pushed on a flat surface of magnitude 45N. The force of friction on the brick is 13 N. that mass of the block is 11kg. A draw a free body diagram B what is the net force acting on the block C what is the acceleration of the block?