A 400-volt DC series motor, of total armature and field resistance of 0.7 , draws 50A at full-load. The full-load speed is 500 rpm and the constant loss is 1500W. Assume that the magnetic circuit is unsaturated. Find: (i) The full-load shaft torque. (ii) The input current if the torque is doubled. (iii)The speed at that new torque.

Q: A 220 V dc shunt motor draws a current of 50 A from the supply and runs at 900 rpm. Its armature and…

A:

Q: 50 kw, 440V three phase, 6 pole 50 Hz asynchronous motor operates at 6% slip und conditions. At full…

A:

Q: Fill in the following blanks: 1. In order to have sparkless commutation, the brushes should be…

A: 1.In order to have  sparkless commutation, the brushes should be placed along the MNA axis 2.D.C…

Q: 6. A 10 kW, 250 V Shunt motor has an armature resistance of O.5 ohm and a field resistance of 200…

A: The solution is given below

Q: A 460V series motor runs at 500 rpm taking a current of 40A. Calculate the speed if the load that…

A: In this question,  We need to determine the speed if the load that the motor is taking is reduced to…

Q: A four-pole, three-phase induction motor rotatesat 1,700 r/min when the load is 100 N-m. The motoris…

A:

Q: The torque in dc series motors depend on Select one: O a. the square of the field voltage Ob. the…

A: In this question we will write about torque in dc series motor...

Q: By decreasing the stator voltage of induction motor to 80% of its rated voltage, the maximum torque…

A: Torque is directly proportional to the square of voltage. Let the reduced voltage be V'. Then , V'=…

Q: A 240-V, 900 rpm DC series motor takes 25 A at full load. The armature resistance is 0.20 and the…

A: To solve this problem, we'll use the given data and the fundamental principles of DC motor…

Q: A wound rotor, induction motor has a rotor resistance of 0.6 ohms per phase and a rotor leakage…

A:

Q: A 550 V dc long-shunt compound motor has an armature and series field resistances 0.815 Ω and 0.15…

A:

Q: Problem 4. A two-pole induction motor operates with the following parameters: slip = 5%, total…

A:

Q: 3. A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole…

A: The solution can be achieved as follows.

Q: .A 10 kW, 250 V Shunt motor has an armature resistance of 0.5 ohm and a field resistance of 200 ohm.…

A:

Q: (c) Briefly explain the operation of an alternator. A 440 V, shunt motor has armature resistance of…

A:

Q: 5. A 220-volt shunt motor draws 64-Amp and runs at 500 rpm. Armature resistance, 0.25- ohm, field…

A: In this question,  We need to determine the speed of the motor when external resistance is added to…

Q: A 220V shunt motor develops a torque of 135N.m at an armature current of 25A. The torque developed…

A: torque in shunt machine is directly proportional to product of flux and armature current. we will…

Q: B. A 180 V, dc shunt motor drives a constant-torque load at a speed of 1600 rev/min. The armature…

A: Given dc shunt motor Constant torque load at speed 1600 rpm Armature resistance Ra=2 ohm Field…

Q: A simplex wave wound armature has 300 turns and takes 125 A of armature current. The flux per pole…

A: back  emf = flux ×speed ×total armature conductors60×polesarmature parallel paths shaft torque =…

Q: A 240-V, 900 rpm DC series motor takes 25 A at full load. The armature resistance is 0.2 Q and the…

A:

Q: (e) enciency. Q6 A 460-V series motor runs at 500 r.p.m. Taking a current of 40 A. Calculate the…

A:

Q: A 230V DC series motor operates at its full load current and speed of 22A and 750 revolutions per…

A: Types of DC Motor Seperetely excited motor Series Motor Shunt Motor Compound Motor Differential…

Q: The shaft torque of diesel motor driving 100v DC shaft wound generator is 25NM generator the…

A:

Q: A shunt wound de motor has an armature resistance of 2.5N and a shunt field resistance of 1602. The…

A:

Q: A 45-hp dc compound motor takes 75 A at supply mains. It operates at a speed of 500 rpm. The flux…

A:

Q: A 45-hp dc compound motor takes 75 A at supply mains. It operates at a speed of 500 rpm. The flux…

A:

Q: Q2- A 240V, series DC motor has armature and field resistances of 0.32 and 0.4 2 respectively. Its…

A: In this question, we need to determine the speed and current at the reduced torque i.e 60%.It's DC…

Q: A 460V series motor runs at 500rpm taking a current of 40A. Calculate the speed and percentage…

A:

Q: On full load, a 300 V series motor takes 90A and runs at 15 rev/s. The armature resistance is 0.1…

A:

Q: О 1220 гpm

A:

Q: 5. (b) A 6-pole, 50 Hz, 3-phase induction motor running on full load develops a useful torque of 200…

A:

Q: A 440 V, 50 Hz, 4-pole, 3-phase, delta-connected motor has. a leakage impedance of (0.3 +j 5.5…

A: We have given the following problem A 440 V, 50 Hz, 4-pole, 3-phase, delta-connected motor has. a…

Motor Load, Torque, and Power Quality Requirement

An electric motor is a gadget that changes electrical energy into mechanical energy over to follow up on a mechanical burden. The weight set on the motor because of this mechanical movement is known as motor load. Appropriately matching the motor burden to the engine is vital to forestall harm to the engine or wasteful and unnecessary expensive activity. Engines perform such undertakings as moving a thing starting with one spot then onto the next, cutting it, changing its shape, etc. The motors might be evaluated as far as a few variables including power yield, voltage, current, and temperature. Harm to an engine might happen when it is worked under over the top engine load contrasted with its appraised limit.