A 400 V, 50 Hz, four Poles, Y connectedinduction motor hasthe parameters in ohms, given in the table below. Z-0.07-j0.3 2 S-0.04 Assuming the V is voltage of line, and use the approximate circuit, detemine: A What is the stator current? B. Statorpower factor? C. What is the torque of the loadunder these conditions? Z-0.08+j0.3 R-50n X-10 2

A 400 V, 50 Hz, four Poles, Y connectedinduction motor hasthe parameters in ohms, given in the table below. Z-0.07-j0.3 2 S-0.04 Assuming the V is voltage of line, and use the approximate circuit, detemine: A What is the stator current? B. Statorpower factor? C. What is the torque of the loadunder these conditions? Z-0.08+j0.3 R-50n X-10 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 240 V, DC shunt motor draws 15 A while supplying the rated load at a speed of 100 rad/s. The armature resistance is 0.5 Q and the field winding resistance is 80 Q. The net voltage across the armature resistance at the time of plugging will be
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
Induct.motor.
I need the answer as soon as possible
A 3-phase 50 Hz I.M. has a rated torque = 16.7 N.M and maximum torque = 40.5 N.M. If its rated speed = 910 R.P.M, the :speed at maximum torque will be %3D R.P.M 578.28O R.P.M 421.640 R.P.M 590.160 None O
Q4) What is the effect in series motor if you assume V = Eb , with low resistance fielding winding ? a) b) The given information about series motor on full – load (with that the flux is proportional to the field current) is a ) takes ( 78A) and runs at (850 r.p.m) , the series winding resistance is (0.04 2) , with diverter in parallel with the field winding is a (0.18 2) and the armature resistance is (0.09 S2). ( 220 V Neglected the iron, friction and windage losses. Determine the efficiency , speed when developing full load torque ,the maximum efficiency .
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
-A 250V, DC series motor has total resistance of 0.8 Q. Its full load current and speed are 10 A and 1500 r.p.m respectively. If the torque is reduced to 50% .Determine the current and speed. Assume straight line magnetization characteristics.
Q2) Determine the back e.m.f at this load of series motor has a series field resistance of (0.301 2) and an armature resistance of (0.1892).It is connected to a (220 V) supply and at a particular load runs at (1500 r.p.m) when drawing (16.2 A) from the supply, if that this cases a three times of flux. Calculate the speed of motor when the load is changed such that the current is increased to (32.23 A).
Reducing the supply voltage so that Vnew = Vold / V3 reduces the maximum torque of the motor so that Tmaxnew= ...Tmaxold . * .... ...
On full load, a 300 V series motor takes 90A and runs at 15 rev/s. The armature resistance is 0.1 ohm, and the series winding resistance is 50 mohm. Determine the speed when developing full load torque but with a 0.2-0hm diverter parallel to the field winding. (Assume that the flux is proportional to the field current.
a 220 V dc shunt motor has armature resistance 0.23 ohm, on load it takes armature current 40 A and turnes at 720 rpm, if the flux of motor is reduced by 10% without changing the load torque . Find the new speed of the motor.