A 40 kVA, single-phase transformer has 400 turns on the primary and 100 turns on the secondary. The primary is connected to 2000 V, 60-Hz supply. Determine the maximum value of the flux. A. 0.0187 Wb C. 0.0157 Wb

A 40 kVA, single-phase transformer has 400 turns on the primary and 100 turns on the secondary. The primary is connected to 2000 V, 60-Hz supply. Determine the maximum value of the flux. A. 0.0187 Wb C. 0.0157 Wb

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Related questions

Q: An iron core is most often used in an AC transformer to 1.provide a better coupling between the…

A: An AC transformer is a device used to transfer electrical energy between two or more circuits…

Q: In transformer, the hysteresis loss depends on, load current only frequency only flux density both…

Q: 10. In a transformer, the leakage flux of each wind- ing is proportional to the current in that…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Calculate the primary leakage reactance of a transformer, supplying a load current of 10 A and 60…

A: Inductance = No. of turns×FluxCurrent Leakage inductance in primary = No. of primary turns×rms value…

Q: A single-phase 500 V/100 V, 50 Hz transformer has a maximum core flux density of 1.5 T and an…

Q: E In a transformer, the core loss is found to be 52 W at 40 Hz and 90 W at 60 Hz measured at same…

A: It is given that:

Q: Question three: A single phase, 4600/460 V, 60 Hz, transformer is connected to a 60 Hz, 4600V power…

A: In the single phase transformer 4600/460V , 60Hz Maximum flux density Bm= 0.85T Per turn induced…

Q: Calculate the voltage per phase for a 1500 rpm, 4 pole alternator having a double layer winding with…

A: It is given that:-

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

60. A 40 kVA, single-phase transformer has 400 turns on the primary
and 100 turns on the secondary. The primary is connected to
2000 V, 60-Hz supply. Determine the maximum value of the flux.
A. 0.0187 Wb
B. 0.0148 Wb
C. 0.0157 Wb
D. 0.0179 Wb

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

3. The maximum flux density in the core of 240/2400 V, 50 Hz, single phase transformer is 1 Wb/m² if the e.m.f. per turn is 8 V, the area of the core is a) 0.132 b) 0.086 c) 0.241 d) 0.036 (125 mark)
The path of a magnetic flux in a transformer should have O High resistance O Low reluctance O Low resistance O High reluctance
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
Determine the peak-to-peak ripple and dc output voltages in Figure 2. The transformer has a 48 V rms secondary voltage rating, and the line voltage has a frequency of 60 Hz. (you may neglect Rsurge). 120 V rms 00000 ellee Figure 2 Rug www 10 100 F ww R₁ 3.3k
A single-phase transformer is required to step down the voltage from 1100 V to 230 V at 50 Hz. The maximum value of the flux in the core is 0.20 Wb. Determine the number of turns in the winding on both sides.
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.
Question three: A single phase, 4600/460 V, 60 Hz, transformer is connected to a 60 Hz, 4600V power supply. The maximum flux density in the core is 0.85 T. If the induced voltage per turn in 10V, determine (a) The primary turns (N1) and the secondary turns (N). (b) The cross-sectional area (A) of the core.
AC Machinery Fundamentals A three-phase delta-connected six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in each phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rotation of the magnetic field is 1000 r/min. What are the resulting phase and terminal voltages?
A single-phase transformer is required to step down the voltage from 1100 V to 400 V at 50 Hz. The [5]core has a cross-sectional area of 25 cm? and the maximum flux density is 5Wb/m?. Determine thenumber of turns of the primary and secondary windings.
I only have 40 minutes
Solutions please
1. A 100 kVA, 3300/400 V, 50 Hz single phase transformer has 110 turns on the secondary. Determine: i. The number of turns on the primary. ii. The maximum value of the flux in the core. iii. The approximate value of primary and secondary full load currents.