A 4.00 (+0.01) mL Class A transfer pipet is used to transfer 4.00 mL of a 0.328 (+0.005) M Cu2+ stock solution to a 100.00 (+0.08) Class A volumetric flask. Deionized water is used to bring the flask to volume. Calculate the concentration of the diluted soluion in the volumetric flask and report its absolute uncertainty. Significant figures are graded for this problem. To avoid rounding errors, do not round your answers until the very end of your calculations. [Cu²*] = 0.0117 M 0.095 M

A 4.00 (+0.01) mL Class A transfer pipet is used to transfer 4.00 mL of a 0.328 (+0.005) M Cu2+ stock solution to a 100.00 (+0.08) Class A volumetric flask. Deionized water is used to bring the flask to volume. Calculate the concentration of the diluted soluion in the volumetric flask and report its absolute uncertainty. Significant figures are graded for this problem. To avoid rounding errors, do not round your answers until the very end of your calculations. [Cu²*] = 0.0117 M 0.095 M

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

K 2
6. The concentration of caffeine in an energy soft drink was determined by standard addition using HPLC. The following procedure was used: a standard caffeine solution was prepared by adding 0.09850g of caffeine to 25.0 cm3 of water.A series of solutions were prepared by adding known volumes of the standard solution to the soft drink before diluting to 100 cm3. The volume of standard and the caffeine peak area are shown in the table: Energy Drink (cm3) Added caffeine Std (cm3) Peak area 15 0 965 15 5 1352 15 10 1739 15 15 2126 15 20 2513 Determine the concentration of caffeine in the soft drink as mg cm-3. A. 3.3 B. 2.3 C. 4.3 D. 7.3
A calibrated pipet delivers a mean volume of 24.991 mL with a standard uncertainty of ± 0.006 mL. What is the uncertainty if you deliver four aliquots to reach 100 mL?
The standard solution is prepared by dissolving a known mass of zinc pellets with conc. HCl. The solution is then neutralized, transferred into a 250 mL volumetric flask and filled to the calibration mark. If 0.9809 g of Zn was weighed using an electronic balance with a relative uncertainty of ± 0.01 % and the 250 mL volumetric flask has a known relative uncertainty of ± 0.06 %, what would be the absolute uncertainty of the concentration of the solution? The molecular weight of the zinc pellets is 65.39 g/mol
urgent please
Using the data and formula shown, Find the slope, intercept, and of the calibration curve. Construct a calibration curve.
If an uncalibrated 5 (±0.03) mL pipet is used to deliver a total of 15 mL, what is the uncertainty delivered in the 15 mL?
A calibrated pipet delivers a mean volume of 24.991 mL with a standard uncertainty of ± 0.006 mL. What is the uncertainty if you deliver four aliquots to reach 100 mL?
SrCl, Observations B|I|U X X + fx | ®| D e Normal Activated charcoal observations Normal BIU fx| 田=| || 的|| || In 1. Based on your understanding of color's relationship to wavelength, identify the approximate wavelength of light (nm) emitted by strontium when it was burned. (No quantitative data was collected for this; you are giving an approximate value only, based on what you observed.) Explain your reasoning in full, making sure to cite specific data and observations to support your answer. Normal BIIIU X:| X'|- EE = fx| DI e 2. While boiling potatoes for dinner in salted water, the pot boils over and you notice that the flame on your gas burner turns to bright yellow-orange. How would you explain the appearance of a color in the previously blue flame? Normal BIIU X X + 田=|IT| 3. What would you conclude about chloride based on your results in the flame tests? Xe | X° | → EI fx| fr DI e E E IT E IT Normal BIIU 4. Place the metal solutions you tested in order of increasing energy…
You are in the lab preparing copper solutions for the MICRO lab this week. You measure 0.1035 (±0.0001) g of copper metal and dissolve it in a few mLs of concentrated nitric acid. This solution is diluted to the mark with water in a 50.00 (±0.05) mL volumetric flask. You withdraw a 5.00 (±0.01) mL aliquot with a volumetric pipet and deliver it to a 100.00 (±0.08) mL volumetric flask. After dilution to the mark with water, calculate the concentration and the absolute error in a solution of copper in ppm (assume ppm = 1 µg/g = 1 µg/mL = 1 mg/L).
After determining the absorbance of several standards of known concentration, the trendline for a calibration curve (AKA a standard curve) plotting absorbance (y-axis) against concentration (M, x-axis) is determined to be y = 4.943x + -0.0001 The absorbance of a solution of unknown concentration is determined to be 0.48. Calculate the concentration of the unknown solution in M. Give your answer to three decimal places.
1) Report the results of this calculation along with both the percent relative and absolute uncertainties. 417.3 ± 0.4 × 71.8 ± 0.7(647.21 ± 0.2 − 182.3 ± 0.4) Absolute uncertainty:Percent uncertainty: