A 4-m bar of negligible weight rests in a horizontal position on the smooth planes shown in the Figure, if T = 30 KN and x = 1 m. Determine the angle e at which the bar will be inclined to the horizontal when it is in a position of equilibrium. * 1 m P = 20 kN 30° 45° 4 m O 22.86° O 28.68° O None of the above 23.88° 26.68°

Q: 100 kN 45° EF, 200 kN 200 kN 30 100 kN 193.30 103.40 173.8 273.8

A: Upon resolving the forces  We can find the Summation of horizontal forces and summation of vertical…

Q: For the given parallel forces, determine its resultant and its location from point A. 25KN/m 20KN/m…

A:

Q: 2.5 m 1.5 m w = 5 kN/m MB = 2 kN.m A В

A:

Q: A wooden beam ( sg = 0.64) is 100mm by 100mm by 6m and is hinged at A as shown in figure2. Assuming…

A: Specific gravity of wooden beam=0.64 Area of beam=100*100 mm2

Q: At what angle e must the 350-lb force be applied in order that the resultant R of the two forces…

A: Given R=700 lb

Q: At what angle emust the 300-lb force be applied in order that the resultant R of the two forces have…

A: Given data: R=730 lb

Q: P.1.3 The equation of a velocity distribution over a plate is u=1/3 y -y' in which the velocity in…

A:

Q: Problem 3 The beam of negligible weight is supported by two springs. If the beam is horizontal and…

A:

Q: Determine the force P required to force the 17° wedge under the 94-kg uniform crate which rests…

A: Given data:- The given, θ=17° The given mass is, 94 kg The given coefficient of friction is, N=0.28,

Q: Solve for: 1. Maximum W in kN if each leg resist 10.098 kN. 2. If W is 49 kN. what is the force…

A: ##Solution of given problem part1, 2, 3 of mechanics ###3d vector forces##

Q: The bar below is subjected to uniaxial tension. Assuming that the bar material behaves elastically,…

A:

Q: In the figure below, the block weight is 200 N, upslope force A = 50 N, and downslope force B = 20…

A: Will the block remain in stable equilibrium or not?

Q: Determine the force P required to force the 16° wedge under the 97-kg uniform crate which rests…

A:

Q: 17- Calculate the value of 810 for the solution of the system given in the figure with the force…

A:

Q: termine the reactions at support and thne forces acting on each member. By applying 1 uni oad…

A: In addition to its initial horizontal speed, a projectile's horizontal displacement depends on its…

Q: Determine whether the block shown is in equilibrium and fınd the magnitude and direction of the…

A:

Q: Situation 3. Given the inclined force below: A 6 m B 5 C 3 Hinge 4 m 117 kN 4 65 kNm 6 m 7. What is…

A:

Q: Calculate the stiffness(k) and natural period(T) of the structure as shown in the picture. (Ignore…

A: Equivalent lateral stiffness(K) of the frame is given by:- K=12EIL3+12EIL3=24EIL3     Given,…

Q: E F G 1[KN] A D Figura 2 B 2.

A:

Q: A block is resting on a 30° inclined plane with a µ = 0.3. Find the required force P acting…

A: Let us estimate the force P in step 2.

Q: The ends of a 0.25kg rod AB are constrained to move along slots cut in a vertical plate as shown. A…

A: Mass of rod = 0.25 kg spring constant = 3 N/m θ= 45° To determine: angular velocity at position 2

Q: A cantilever beam carries a partial uniform load w = 5 kN/m and a point load of P = 10 kN as shown…

A: In double integration  EI d2y/d2x = - Mx  Negative sign is taken to consider downward deflection…

Q: Analyse the structure shown in Figure using consistent deformation methods, then draw the Shear…

A:

Q: FORCE SYSTEM IV. EQUILIBRIUM OF NON-CONCURRENT Example Problem 2: A 12-ft bar of negligible weight…

A:

Q: Using the Slope deflection method, calculate the reactions at the supports of the beam shown: Assume…

A: Given

Q: Calculate the horizontal and vertical displacement of point B. Rod cross-sectional areas A = 1050…

A:

Q: Given a bar X with length of 3.7 meters, determine where the 3.2 kN force must be applied in order…

A:

Q: 8 From the given determinate beam, which of the following provides the displacement of point B in kN…

A: Given:Required :Deflection at B

Q: Determine the force P required to force the 10° wedge under the 77-kg uniform crate which rests…

A: The forces in the member of structure can be resolved into components for the analysis of the…

Q: For the simply supported beam carrying the concentrated load P = 223 N at its midspan, determine the…

A:

Q: For the beams below, determine the location of the maximum deflection using double integration…

A:

Q: a) Nodal displacements and slopes b) The forces in each element c) Reactions SHOW YOUR WORK 10 kN/m…

A: Step 1  Given Data:    To determine:-a Nodal displacement and slopes                        b Forces…

Q: Determine the reactions at support and the forces acting on each member. By applying 1 unit load…

A:

Q: Analyse the structure shown in Figure using consistent deformation methods, then draw the Shear…

A: Using method of consistent deformation ### drawing of SFD and BMD#### Assuming EI=1×10^4 KNm^2

Q: Topic: Mohrs Circle. A circular shaft (Diameter 0.5 m) is under torsional load. Mohr's circle radius…

A: Given data in question  Diameter 0.5 m Radius 50 MPa To find out  Torsional load in kNm Note Since…

Q: 18,1:The diameter of the AB bar shown in the figure is d=5 cm and the material it is made of is…

A: FBD -

Q: Refer figure 1: Determine the deflection (delta) in mm at point B. Use E = 200 GPa and I = 2100 mm^4…

A: E = 200 GPa I = 2100 mm4 Determine the vertical reaction at hinge support and deflection at point-B…

Q: A 12 ft bar of negligible weight rests on the smooth planes as shown. Determine the angle a at which…

A:

Q: 2. Determine the horizontal force P in the figure to start the 400 lb wedge (a) moving to the right…

A:

Q: : Determine the amount of deflection at free also the maximum deflection. Use W = 35 kN/m, M = 15…

A:

Q: For the figure shown below: a. Calculate the magnitude, direction, and sense of the resultant force…

A:

Q: Item Number 1. Solve for the reactions, the midspan deflection, and the slope at the midspan. Use…

A:

Q: compute the value of P and .

A: Given Data Sphere Weight, W=300 kN Weight passing Over, W1=200 kN Pulley is frictionless Angles,…