A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E = 2 x 106 kg/cm² and the unit weight y of the steel to be 7.9 x 10-³ kg/cm³. a) Determine the cross-sectional area of the tape. Hint: y = W/V

A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E = 2 x 106 kg/cm² and the unit weight y of the steel to be 7.9 x 10-³ kg/cm³. a) Determine the cross-sectional area of the tape. Hint: y = W/V

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000MPa and a = 11.7- m C" Neglect bending of the beam. A=640mm2 A=320mm2 A C D 1.2m 0.8 m 1.2 m 54KN What is the stress of rod B if there is no change in temperature in MPa?
111. two decimal places
A rectangular bar is subjected to tensile forces of 2230 kN. Use E = 110 GPa and v= 0.34. Determine the change in the dimension of its cross-section along X and Z directions. Also, calculate the change in the volume of the bar. Z 80 mm 90 mm 2230 KN 2230 KN Y 1.75 m X ----
SITUATION E:A 30 m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg supported for full length. The tape was used in measuring a line 938.55 m long on a smooth level ground under a steady pull of 10 kg. Assuming E= 2x106 kg/cm2 and the unit weight of steel to be 7.9x10-3 kg/cm³. Determine the total correction for increase in tension -0.068 m +0.068 m -0.038 m +0.038 m
A 30 m. Steel tape weighing 1.45kg is of standard length under a pull of 5kg supported for full length. The tape was used in measuring a line 938.55 m. long on a smooth level ground under a steady pull of 10kg. Assuming E = 2 x 106 kg/cm2 and the unit weight of steel to be 7.9 x 10-3kg/cm3. Determine the cross-sectional area of the tape in cm2. Determine the correction for increase in tension Determine the correct length of the line measured.
Problem 2. A 30 m steel tape weighing 14.23 N is of standard length under a pull of 7 kg, supported for full length. The tape was used in measuring a line 789.25 m long on smooth level ground under a steady pull of 12 kg. Assume E = 2 × 106 kg/cm² and the unit weight y of the steel to be 7.9 × 10-3 kg/cm³. a) Determine the cross-sectional area of the tape. Hint: y = W/V b) Determine the correction due to pull for one tape length. c) Determine the total correction due to pull. d) Determine the corrected distance.
Q.uestion 23.
solve for deformation in figure B. given V= 10-0 and area = 2.0in^2
Problem 2 For the simply supported beam shown below, determine whether the beam is cracked or un-cracked under the applied loads, use f'e = 25 MPa, if the beam is cracked calculate the bending stresses in the beam using the transformed area method. 20 KN 300 mm 4 kN/m A↓ D 3025 k 3 m 3 m 500 mm - աա St
The fixture shown in Figure 5 is fixed at point A and free at point C. The frame is made from a steel bar 50 mm wide and 75 mm thick. Assuming Young's modulus for steel to be 200 GPa, determine the vertical deflection at C due to the applied load of 5 kN. Use Castigliano's theorem and ignore any axial or shear deformations. A 4.5 m Figure 5 kN с T B 5 (not to sca 1.5 m Cross section ↓ 0 ↑ h b = 50 mm = 75 mm
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
A 30-m steel tape weighing 1.45 kg is of standard length under a pull of 5 kg, supported for full length. The tape was used in measuring a line 938.55 m long on smooth level ground under a steady pull of 10 kg. Assuming E = 6. 2 2.0 x10° kg/cm and the unit weight of steel to be 7.9 x10 3 3 kg/cm, determine the correct length of the line measured. а. 948.1 m b. 938.59 m С. 950 m