a 30 m steel tape was used to measure aline and the initial pull is 5.5 kg. Pull at time of measurement is 8 kg. Weight of tape is 0.05 kg/m. E = 2.1x106 kg/cm2. Cross section =0.04 sq.cm. Measured distance between two points = 471.450 m in an inclined surface having a gradient of 3%. Find the correct horizontal distance between the two points.

a 30 m steel tape was used to measure aline and the initial pull is 5.5 kg. Pull at time of measurement is 8 kg. Weight of tape is 0.05 kg/m. E = 2.1x106 kg/cm2. Cross section =0.04 sq.cm. Measured distance between two points = 471.450 m in an inclined surface having a gradient of 3%. Find the correct horizontal distance between the two points.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam loaded as shown in the figure 1, determine the slope at A in degrees using Double Integration Method. Consider 150 mm x 150 mm section and E = 200 GPa. Enter the absolute value only and round-off your answer to 3 decimal places.
using unit load method I can't get to the solution
answer using Conjugate Beam Method and show complete solution. Problem no. 1 Determine the slope and the displacement at the end C of the beam. . 8 kN 4 kN 3 m 3m 3m
Solve Using Virtual Method for Beams to get the answers. The answers must be: Slope = 23.25kN•m² while Displacement= 87.25 kN•m³/EI
For the loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at the free end, and (c) the slope at the free end. Assume that EI is constant for the beam. Let w = 8 kN/m, L = 3.0 m, E = 205 GPa, and I = 100 x 106 mm4. Cut a cross-section through the beam at any point and draw a free body diagram. Determine the internal bending moment M(x). The diagram shows M(x) in its positive direction. Your answer may be negative. Check your equation by solving for M at x = 1.5 m.Answer:M(x = 1.5 m) = kN·m
PROBLEM 5 The uniform block, 4'x 3'as shown weighs 2001b. It is pulled up the incline by the force F= 250 lb. Determine the maximum and minimum values of d so that the block does not tip over as it slides up the incline. The coefficient of friction is 0.21. +3 IL
By Using slope deflection method analyze two span continuous beam ABC. Then draw Bending moment & Shear force diagram. (EI constant)
AnswerASAP
Consider the beam shown in (Eigure 1). Suppose that M= 30 k ft. El is constant. Solve this problem using the moment-area theorems Figure 15 ft B -9 ft 1 of 1 M Determine the displacement at C measured upward. Express your answer using three significant figures. 195] ΑΣΦ ↓↑ vec Ac = Submit Part C Request Answer 0c = D ? Determine the slope at C measured counterclockwise from the positive x axis. Express your answer using three significant figures. 1ΨΕΙ ΑΣΦ ↓1 vec x 1 k-ft³ EI ? X 1 k-ft² EI
Please answer using Conjugate-Beam Method and show complete solution.
A 410-kg block is resting on a 52 deg inclined plane with a coefficient of friction = 0.51. Find the required horizontal force P (kN) that is necessary to prevent motion DOWN the incline. ROUND OFF TO TWO DECIMAL PLACES.
Must be solved using Castigliano's theorem