A' 3.214 гот B SOKN fom с lom 4 Tooky D you

Q: Determine the maximum load based on shear design at critical section and at 1.5m from the support of…

A: the critical section for shear stress is if the support reaction introduced compression in end…

Q: es Required information Problem 01.061- A two link assembly with point loads Two horizontal 13-kip…

A:

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 15 ເຄດາ -…

A:

Q: determine the largest allowable spacing of rivets that join (a) the angle bars and the top plate;…

A: The Working stress of shear and bearing is given as 100 and 250 MPA yu

Q: A steel channel is used as a purlin of a truss. The top chord of the truss is inclined at a slope of…

A: Weight of the purlin = 79 N/mDead load, DL = 720 N/m2Live load, LL = 1000 N/m2Wind load, WL = 1440…

Q: 1. The beam AB is fixed to the wall and has a uniform weight of 80 lb ft. If the trolley supports a…

A: Hi! Thank you for the question As per the honor code we are allowed to answer only one question at a…

Q: Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded…

A: A loaded beam is given and it has been asked to determine location of maximum flexural compressive…

Q: tion. The tie rod is connected at B and C by 20-mm-diamet h of 220 MPa, and each of the pins has an…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each

A:

Q: Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point…

A:

Q: H.W. #4: A pin connected truss is loaded and supported as shown, determine: a) The normal stress in…

A: Determinea. The normal stress in member DE if it has cross sectional area of 750 mm2. b. The minimum…

Q: The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450mm².…

A: 3 suspended bars are given, of equal cross-sectional area as shown in the figure above and it has…

Q: Find the max compressive and tensile normal stress of the beam below

A: Given Data  Determine the maximum compressive and tensile stress of the beam.

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: Given data: Shear stress τ = 70 MPa Bearing stress σ = 140 MPa Diameter of rivet d = 19 mm   For the…

Q: B 5 m 5 m 5 m 5 m, 5 m A 5 m 5 m E 30 kN 20 kN From the given truss, which member has an internal…

A: We will employ method of joint to every joint untill we find the member having compressive force of…

Q: In the calculation of the friction and wobble, the value of the alpha for a section where the tendon…

A:

Q: A welded plate girder is subjected to factored bending moment 9500 kNm, having span 25 m as shown in…

A: For a welded plate girder, factored bending moment: 9500 kNmspan length  25 mk = 180

Q: An I section girder or stanchion is constructed from two 80mm x 12mm flanges joined by an 80mm x…

A: I section girders: I sections girders are most commonly used in the construction of bridges. These…

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

A:

Q: 2. Determine the force in members EF, EP, and LK of the Baltimore Bridge Truss, indicate if the…

A:

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A:

Q: A T-beam with the cross-section shown above is subject to the loads shown. a) Determine the second…

A: Given:- To find:- Second moment of area SFD and BMD Normal stresses at A, B and C Concept:-…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

A:

Q: Using the unit load method, find the vertical displacement at end (A) in the composite frame shown…

A: Given Data :  Axial rigidity = 35000 KN , Flexural rigidity = 10500 KN/m2 Let the force in cable is…

Q: D 30 kN 70 kN 2 m 12 mm-thick gusset plate 10 -mm-thick 2 m angle 1.5 m-15 m- 15 m--15 m 8 mm-thick…

A:

Q: The idealize model for suspension bridge is shown in the figure. The truss are pin connected at a,…

A: We have to determine the design diameter of the cable if the allowable tensile stress is 150 MPa and…

Q: Determine the stresses in each member of the truss shown using method of joints. 40 kN C 10 kN -1.25…

A: Objective: To determine the internal forces in each member of the truss using the method of  joints.…

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A: Step 1:Step 2:Step 3: Step 4:

Q: The beam shown below has a cross section of channel shape with width b3200 mm and height h=80 mm,…

A:

Q: 2,300 mm A 1,150 mm 1,600 mm 75 kN

A:

Q: Consider the truss structure and the loading given below. a) Compute the average axial stress on…

A: Take equillibrium at point B to find force

Q: Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and…

A:

Q: 3. Determine the forces FG, EF & AC of the truss using method of joints.

A: Given a truss and it is asked find forces in members FG, EF and AC

Q: The figure below are cables ( circular section) supporting a MN kN. Find the axial stress of each.…

A:

Q: 18 kN 25 kN 8m D DE 6m 10 kN Figure 1

A:

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Given data: