equate 1 and 2, Thank

Q: What is the meaning of soundness of cement? Lütfen birini seçin: O A. Ability to binding capacity O…

A: Soundness of cement:

Q: SFD of a beam is shown in the figure. Identify the location and nature of supports. Draw loading…

A:

Q: hat does C sub c refer to?

A: CC = Coefficient of compression  Which is the ratio of change of void ration before and after…

Q: 2) Calculate the stresses and strains in the x, y and z directions for this aluminum block. For…

A: The aluminium block is given as E = 70 GPa ν=0.33 To find:- Stress and strain in x, y and x…

Q: Could you help me figure out the symbols and what they stand for and categorize them. Thank you

A: To find- The symbols used in the map and categorize them.

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: 5. Which one of the following stages is applied in reverse Engineering technique: A) Evaluation B)…

A: Reverse engineering is the process of extracting knowledge from anything mam-made & reproducing…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: A ship has a metacentric height of 0.75 m and its period of rolling is 10 seconds. The relevant…

A: Given:-    Metacentic height = 0.75 m   Period of rolling = 10 second Find relevant radius of…

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: Estimate the uplift pressure under bottom left corner of this dam If the entire dam sits 2ft below…

A: coefficient of permeability, Height, Height,

Q: GIVEN FIGURE SHOWN, DETERMINE THE LOCATION OF CENTROIDAL X AND Y. Y 4" 2 in. radius 9" 12" X- -X 2"…

A: NOTE : As per our guidelines we are supposed to answer only one question. kindly repost another…

Q: Complete the chemical reaction below. ? °C CaCO3 CaO CO2

A: Given chemical reaction is, CaCO3→? °CCaO+CO2   The standard Gibbs free energy of reaction is…

Q: How is unit weight expressed in primary dimensions?

A: Unit Weight is defined as the Weight of soil per unit volume.

Q: A square gate shown is 6-ft on all sides is hinged at the top of the gate, and is restraine by the…

A: INTRODUCTION: This is a hydrostatic force acting on a inclined plate type question. we have to know…

Q: A subcontractor must join two wooden planks to lengthen a tension member (see Figure 5). It does…

A: E = 140MPa α = 13.5x10-5/°C σw = 30MPaσs = 30 MPa Bolt shear = τb = 70MPa Change in temperature = ∆T…

Q: Find the upward deflection at the tip for the frame and loading below. Use P = 8 kips, a = 12 ft, b…

A:

Q: The shear diagram is shown in the figure, determ 90KN 2m -30KN 2m 1m

A:

Q: Q3 Draw shearforce and bendingmoment diagram for thefollowing beam. 5kN/m 3kN/m 5m 4m 12m

A: support reaction: ∑FY=0RA-3×5-12×5×3=0RA=22.5 KN∑MA=0-MA+3×5×9.5+12×5×3×5=0MA=180 KN-m

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: What information can you derive from a given designation of an ASTM standard such as E 119-95a

A: ASTM E119-95a  indicate Fire tests of Building construction and materials for a non bearing fire…

Q: The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B…

A: Given Data Cross sectional area at section a-a = 1in. × 0.25 in. Diameter of bolt shank (d) = 0.5…

Q: Choose the correct one and explain it

A: Given data : Normal stress in X direction (σX)=5 MPaNormal stress in Y direction (σX)=5 MPaMajor…

Q: A number of different adhesive joint geometries are shown below. Which ONE of the following lists is…

A:

Q: Can you please explain where all the values came from?

A: Theoretical oxygen demand (ThOD) is indeed the estimated quantity of oxygen needed to completely…

Q: 21. Given in the accompanying tabulation are the observed data for a closed traverse obtained from a…

A: To Determine latitude and departure of each course, linear error of closure, bearing of the side of…

Q: 4. A 20 m long uniform bridge has a mass of 2500kg and is supported by two posts that are 2m in from…

A:

Q: Explain the difference between nominal and actual size.

A: Nominal measurements- The “nominal” size of a piece of lumber is typically what’s referred to by the…

Q: please explain where 1/32 come from?

A: Given, D = 0.2 in τmax = 20 ksi G = 12 x 106 psi

Q: how the step 2 come and also in step 1 how did u take the term (20-x)?? can you explain this?

A: In step 2, influence line diagram is drawn using Muller Breslaw principal which states that to…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: Draw S.F.D. and B.M.D. for Beam JZ below by using the Moment Distribution Method. 14.1 kN/m EI EI J…

A:

Q: The managers in a new gypsum plant need to make a decision between three gypsum reservoirs located…

A: Gh

Q: Please show all steps and carry the units. Thank you

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Q-6 It is known that mortars prepared with Portland cement have higher strength than lime. • Why are…

A: Given data  Lime Mortar To be discussed  Why lime mortar is used in restoration of old buildings

Q: Can you please redo this and explain how you got what you got? I dont understand concept and show…

A: To draw a cross-section AA' and BB' for the given section.