A 3.0 kg bag resting on the ground is tied to a vertical cord. The cord of negligible mass passes through a cylinder with a groove in which a cord can run. The otherend of the cord is attached to a 6.0 kg ball, as shown in the figure. The cylinder is 4.0 cm in radius and has a mass of 125 kg. The friction force about the rotation axisproduces a torque of 1 Nom. Calculate the time needed for the 6.0 kg ball to hit the ground if it is released from a height of 1.25 m without initial speed.3 kgM = 1.25 kgIR = 4 cm6 kgGround1.25 m

Answered: Image /qna-images/answer/484daf85-8a83-4bcf-92c5-d4200dbd72ed.jpg

Answered: A 3.0 kg bag resting on the ground is…

Similar questions

A uniform rod is set up so that it can rotate about an axis at perpendicular to one of its ends. The length and mass of the rod are 0.769 m and 1.09 kg , respectively. A force of constant magnitude ? acts on the rod at the end opposite the rotation axis. The direction of the force is perpendicular to both the rod's length and the rotation axis. Calculate the value of ? that will accelerate the rod from rest to an angular speed of 6.03 rad/s in 8.01 s .
Flywheels are large, massive wheels used to store energy. They can be spun up slowly, then the wheel's energy can be released quickly to accomplish a task that demands high power. An industrial flywheel has a 2.0 m diameter and a mass of 260 kg. Its maximum angular velocity is 1400 rpm. A motor spins up the flywheel with a constant torque of 58 Nm. How long does it take the flywheel to reach top speed? How much energy is stored in the flywheel?
A 350-N sphere 0.20 m in radius rolls without slipping 6.0 m down a ramp that is inclined at 31° with the horizontal. What is the angular speed of the sphere at the bottom of the slope if it starts from rest? rad/s
A ball with a weight of 70 N hangs from a string that is coiled around a 3 kg pulley with a radius of 0.4 m. Both the ball and the pulley are initially at rest. The rotational inertia of the pulley is 0.5mr2 and the ball is released from rest. Calculate the ball's velocity after it falls a distance of 2 meters.
The 22-cm-diameter disk in figure can rotate on an axle through its center.What is the net torque about the axle?
An Atwood's machine consists of blocks of masses m, = 11.0 kg and m, = 19.0 kg attached by a cord running over a pulley as in the figure below. The pulley is a solid cylinder with mass M = 9.60 kg and radius r = 0.200 m. The block of mass m, is allowed to drop, and the cord turns the pulley without slipping. T2 тi т2 (a) Why must the tension T, be greater than the tension T,? This answer has not been graded yet. (b) What is the acceleration of the system, assuming the pulley axis is frictionless? (Give the magnitude of a.) m/s? (c) Find the tensions T, and T2 T2 =
A person with an axe to grind is using a whetstone. The whetstone is connected to a motor which keeps it rotating at 85 rev/min. The whetstone is a solid cylinder of made of a special type of stone of mass 45 kg and radius 20 cm. The heavy axeblade is being pressed onto the whetstone with a steady force of 25 N directed into the centre of the whetstone. Suddenly, the power to the motor is cut but the person maintains the force of the axe on the whetstone. The coefficient of kinetic friction between the axe and the stone is 0.60. The moment of inertia of a cylinder about it's centre of mass is I = ½MR2. (a) Calculate the torque of the frictional force on the wheel. (b) Calculate the total angle through which the wheel turns from the time the power goes off to the time the whetstone stops rotating. (c) How long does it take for the wheel to stop after the power outage?
A force of 3N is applied in the positive y direction and 5.5N in the negative z direction in a situation with a lever arm of 2.7m in the -x direction. What is the magnitude of the torque?
A bowl is rotating on a potter's wheel at constant angular speed as shown. The friction force between his hands and the bowl is 1.70 N total. If the bowl has a diameter of 13.0 cm, how large is the torque on the wheel? Report a positive answer.
A bicycle wheel, of radius 0.300 m and mass 1.16 kg (concentrated on the rim), is rotating at 4.00 rev/s. After 54.2 s the wheel comes to a stop because of friction. What is the magnitude of the average torque due to frictional forces? ____ N⋅m
A toy Ferris wheel that is at rest has a radius of 20.0 cm. A perpendicular force of 1.5 N is applied to the outer most part of the Ferris wheel. The toy Ferris when has a rotational inertia of 0.050 kg m2 . a) What is net Torque applied to the Ferris wheel? b) What is the angular acceleration of the Ferris wheel? k) If the Ferris wheel maintains this angular acceleration for 3.0 seconds, what will its final angular velocity be? d) What will be its rotational Kinetic Energy after 3.0 seconds?
A potter is shaping a bowl on a a potter’s wheel. The wheel rotaes at a constant angular speed. The frictional force between her hands and the clay is 2.25 N. How large is the torque she produces on the wheel if the diameter of the bowl is 14 cm.

SEE MORE QUESTIONS