A 3-bit PCM system with a linear midrise quantiser of step-size A = 1V is used to digitise the signal m(t) = 4 cos(t) V. Assume a sampling rate of four samples per second, with 3 9 15 } 4' seconds, sketch the i) Signal m(t) and label the value of the samples taken ii) Graph for linear midrise quantiser of step-size A = 1V iii) Resulting PCM wave for one complete cycle of the m(t) input signal the samples are taken at t =

A 3-bit PCM system with a linear midrise quantiser of step-size A = 1V is used to digitise the signal m(t) = 4 cos(t) V. Assume a sampling rate of four samples per second, with 3 9 15 } 4' seconds, sketch the i) Signal m(t) and label the value of the samples taken ii) Graph for linear midrise quantiser of step-size A = 1V iii) Resulting PCM wave for one complete cycle of the m(t) input signal the samples are taken at t =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A transistor output noise voltage is measured at 15microvolts when the standardized noise source is at the input. With the noise source removed, a noise voltage of 5 microvolts is measured. Calculate the noise figure.
3. Describe Amplitude Modulator as one of an OTA applications
shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab
A signal has a frequency of 20 Hz and duty cycle of 25%. For this signal, fill in the following Signal Period in mSec Signal off time in mSec Signal on time in mSec
Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
Given the analog waveform as shown with an effective bit rate of 26,000 bits / sec. Determine the minimum sampling rate of a ADC converter if the analog input is sampled at 8 samples per bit. Express your answer in KHz and in at least 3 significant figures. Answer:
Styles 1. The noise produced by a resistor is to be amplified by a noiseless amplifier having a voltage gain of 75 and a bandwidth of 100 kHz. A sensitive meter at the output reads 240 μV rms. Assuming operation at 37° C, calculate the resistance of the resistor. If the bandwidth were cut to 25 kHz, determine the expected output meter reading. (Ctrl) -
i need the answer quickly
Please Solve this Question: Design a Relaxation oscillator (using 1 OPAMP, 3 resistors and 1 capacitor) togenerate a square waveform of period 220us and 50% duty cycle.
An op-amp comparator in a firing circuit can produce waveforms at the output of up to 28 V peak-to-peak without any distortion. An inverse cosine-based firing circuit with a voltage range from +14 to -14 (reference voltage) is used to produce a gating signal for the SCR at the desired delay angle. if the reference voltage is 5.92 volts, the delay angle (in degrees) would be:
Please write legibly 1.draw the small signal model of this circuit. 2. Find the total transconductance Gm 3. Show how Rop was derived
In a Wien bridge oscillator circuit, the value of the resistor andnthe capacitor that form the RC series and parallel branch are given as 200 ohm and 10 mF. What will be the frequency of oscillation?