A 2o0y bubble 7o mm diameten internal frlessure exces g 25 N/mim2 what in tension in soof Silm. has in oilside fresune

Q: For the given state of stress. determine the normal and shearing stresses exerted on the oblique…

A: The result and conclusion are attached here in next few steps:

Q: Attemperator increases the higher heat absorption at high loads to ensure that the desired steam…

A: The given statement is true.

Q: he primary and secondary shear loads on bolt P

A: Given; A steel bar of;  =  10×50 mmCantilevered with two M12 bolts,To support a static load of 4kN…

Q: An airplane is making a level turn at 200 knots while pulling 2.5 g's (n = 2.5). Calculate the turn…

A:

Q: Heat transfer by convection واجب سي (1 )Example S Air at 2 atm and 200 c°is heated as it flow…

A: To find: The heat transfer per unit length of tube and the amount of bulk temperature increases.…

Q: Consider the diagram of a block attached to a wall being supported by a pole. Find the net moment…

A:

Q: 8- A coper road is inserted into a hollow aluminum cylinder . The copper rod projects 0.130 mm as…

A:

Q: Bearings are manufactured to take loads of type: Select one: a. Pure radial loads b. A combination…

A: It is required to give correct answer

Q: Q3. The lamp has a weight 40 N) and is supported by the siX cords connected together as shown.…

A:

Q: The mass of a turbine rotor of a ship is 8 tonnes and has a radius of gyration 0.6 m. It rotates at…

A:

Q: rectangular section the ratio of maximum shear stress to the average shear For a stress is

A: Given data : Rectangular section Width=B Depth=D Shear force=V Average shear stress=ζAvg Maximum…

Q: Determine the cycle efficiency.

A:

Q: Q3/ A beam supports a distributed load as shown. 1- Explain the beam type 2- Draw F.B.D 3- Determine…

A: (1) Since the beam is free at one end and fixed at other end, the beam is a cantilever beam.

Q: •A power station will run 24 hours a day with 7 operators working 8 hours per day and 5 days in a…

A: Given: To find the annual cost

Q: sleeve is 6 poise . The shaft is of diameter 0.5 m and rotates at 210 Prob. 6: The dynamic viscosity…

A: There are two main types of bearings, namely, rolling contact bearing and sliding contact bearing.…

Q: The figure below shows a simply supported beam with an overbang. The beam is made of two types of…

A: σpi=11 mPa     Epi=8 GPaσpl=14 mPa     Epl=12 GPaFind allowable magnitude w=?

Q: A force of magnitude P = 180 N is applied stationary machine handle as shown. Wr. force and moment…

A: the component parallel to the x axis will create a reaction along the negative x axis  component…

Q: {2)What is the maximum gauge pressure of water th OWhat is the maximum gauge pressure of water th.…

A: Given Data : Height (h)=2.5 m

Q: Superheated steam originally at P, and T, expands through a nozzle to an exhaust pressure P.…

A: Given:

Q: 3- A Compound bar composed of three bar as shown .Determine the stress if the temperature change…

A: Calculated stress in brass and aluminum block when it compounded.

Q: A 150 mm diameter orange (P =950 kg/m.K, c= 4150 J/kg.K and k= 0.6 W/m.K), aproximately spherical in…

A:

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Q: learly explain your understandings why a couple cannot produces ny translatory motion (i.e., motion…

A:

Q: 1- A Carnot cycle works on steam between the pressure limits of 7 MPa and 7 kPa. Determine thermal…

A:

Q: Determine the force in members BC, CF, and FE. State if the members are in tehsioH OF 2 m 10 kN 25…

A:

Q: Ratio of soldification time of a cylindrical casting (Height=radius) of that of a cubic casting of…

A:

Q: In the figure shown, what the minimum height (h) t which water must rise in th water tank in order…

A:

Q: (B)Fig.I shows oil of viscosity (0.09 N.s/m*) filled annular space of a cylinder of (11.05 cm)…

A: Given:μ=0.09 N.s/mD=11.05 cm =0.1105 md=11 cm =0.11 mF=20 NL=13 cm =0.13 m

Q: An aeroplane makes a complete half circle of 50 metres radius, towards left, when flying at 200 km…

A: given:Speed, v=200 kmph or 55.56 m/smass, m=400 kgradius of gyration, k=300 mm or 0.3 mEngine speed,…

Q: irough the impeller is con pack at angle of 46° to the et of pump.

A:

Q: cylinder havi th oil of densit axis at an ang

A: we have to find out thrust on bottom of cylinder radius =Rheight=Hangular velocity =ω

Q: 6) Which of the following statement(s) is/are correct? i. The ratio of the test temperature to the…

A: Given Material statement To find The correct statement

Q: Q4) A) What is the difference between R and Ru and how these two are related. B) What is the…

A: 4.) Characteristic Gas Constant (R) :- with help of molar mass of gas and STP values R will be…

Q: In a gas turbine, hot combustion products with the specific heats c,= 0.98 kJ/kgK, and c. = 0.7538…

A:

Q: The advantage of an independent chuck is that the work can be centred to high precision. Select one:…

A: Advantages They can be utilized to hold sporadically molded parts. With the utilize of a dial…