A 240-V, 100 A armature full-load current, 1800 RPM, cumulatively-compounded DC motor is considered in this problem. Its characteristics are given below: RA+Rs = 0.20 $2 RF = 140 2 Radi = 160 2 NF-2000 turns NSE = 16 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: If, A 0 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 What is the full-load speed of this motor? Answers: Write the speed in the first box and the unit in the second box. The full-load speed is:

A 240-V, 100 A armature full-load current, 1800 RPM, cumulatively-compounded DC motor is considered in this problem. Its characteristics are given below: RA+Rs = 0.20 $2 RF = 140 2 Radi = 160 2 NF-2000 turns NSE = 16 turns This motor has compensating windings and interpoles. The magnetization curve for this motor at 1800 RPM is shown in a tabular form below: If, A 0 0.1 0.2 0.4 0.5 0.6 0.8 1.0 1.2 1.6 1.8 2.0 2.2 2.4 EA.V 6.0 25 50 110 135 160 205 235 255 275 285 288 290 291 What is the full-load speed of this motor? Answers: Write the speed in the first box and the unit in the second box. The full-load speed is:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How can the speed of a shunt DC motor be controlled
(c) What are the principle characteristics of DC series motor and DC compound motor, and what are its uses?
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
I need the answer as soon as possible
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
22. A) Why is the power factor of a lightly loaded 3-phase squirrel-cage induction motor very low? a) most of the power supplied to the motor at light loads is magnetization or inductive power b) most of the power supplied to the motor at light loads is resistive power c) most of the power supplied to the motor at light loads is capacitive power d) none of the above B) What happens to the power factor as load is increased on the motor? a) the power factor increases b) the power factor deceases c) remains the same
A DC motor should be operated in a strong field which is due to the What happens to if suddenly goes a) nothing, it continues rotating b) it over speeds c) it stops rotating current if moter if rotating to zero. as before
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
Explain the speed-current, torque-current and speed-torque characteristics of dc series motor.