A 240-kip concentric load P is applied to the granite block shown. 6. 6 m. Determine the resulting maximum value of the normal stress. Specify the orientation of the plane on which these maximum values occur. The resulting maximum value of the tensile stress is The resulting maximum value of the compressive stress is |ksi at 8 = ksl at 8= 1.

Q: 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular,…

A: Given:Average normal stress, σ=3.8 MPaLoad applied, P=1200 Nouter diameter, d=25 mm

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on…

A: (a) The magnitude of load P is 59.04 kips. (b) The shear stress on plane AB is 4.8 ksi. (c) The…

Q: If F1 = 1070 Ib and F2 = 2095 Ib, determine the magnitude of the normal stress produced at point H.…

A: Given: The force, F1 = 1070 lb The force, F2 = 2095 lb

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on…

A:

Q: Three forces, each of magnitude P = 3 kN, are applied to the structure shown. Determine the…

A: Solution.jpg

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: Two equal and opposite couples of magnitude M = 23 kN-m are applied to the channel-shaped beam AB.…

A:

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

A:

Q: 3.5 m r= 0.6e-0.08y² y 0.6 m

A:

Q: Draw Mohr's circle that describes each of the following states of stress.

A: Given data:- σx =-8 ksi σy =12 ksi τxv=-6 ksi To draw:- Mohrs circle

Q: B The two rods AB and AC have diameters of 10 millimeters and 8 millimeters. Determine largest…

A:

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: 6 in. ااه 800 lb

A:

Q: B

A: Given DataHorizontal force at end D of the lever, P=150 lbThe diameter of portion AB of the lever,…

Q: The tee shape shown is used as a short post to support a load of P = 1670 Ib. The load Pis applied…

A:

Q: The hollow steel shaft has a diameter of 65 mm and thickness of 5mm, is subjected to a torque and…

A:

Q: The 1 inch diameter rod is subjected to the loads shown below. Determine the state of stress at…

A:

Q: Determine state of stress at the remaining points (P2, P3 and P4). Calculate the maximum principal…

A: Given: Outer Diameter of the Pole do=115 mm=0.115 m inner Diameter of the Pole di=100 mm=0.1 m To…

Q: Problem 1-37: The plate has a width of 0.5 m. If the stress distribution at the support varies as…

A: Given:Width of the plate, Stress distribution on the support, Length of the plate,

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ =…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.