A 24 ft column shown below, pinned at one end and fixed at the other, is used to suppor a compressive axial load. It has a bracing in the weak axis direction at 1/3 of the length from the pinned end. Select the lightest W 14 section that adequately support the loads PD-400 kips and PL-175 kips. Use A572 Grade 50 steel. /////// L *

A 24 ft column shown below, pinned at one end and fixed at the other, is used to suppor a compressive axial load. It has a bracing in the weak axis direction at 1/3 of the length from the pinned end. Select the lightest W 14 section that adequately support the loads PD-400 kips and PL-175 kips. Use A572 Grade 50 steel. /////// L *

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the Truss member shown, design all the tension members for ASD and LRFD, if the connection for the angle bars are shown. Use A36 STEEL. 100 mm 150 mm 2.5 m B SERVICE DEAD LOAD =300 KN SERVICE LIVE LOAD = 200 KN 2 m 2 m 2 m 2 m
Select a WT section for the compression member shown in Figure . The load is the total service load, with a live-to-dead load ratio of 2.5:1. Use Fy 5 50 ksi. a. Use LRFD. b. Use ASD
Reinforce an existing simply supported W16 x 36 beam made of A36 steel to carry a service dead load of 0.5 kip/ft and a service live load of 1.1 kip/ft. The beam spans 25 ft and is fully braced by the floor. WELD ALONG THE LENGTH AND ENDS WELD ALONG THE LENGTH AND ENDS A (b) (s) EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM CONTINUOUS PLATE EXISTING BEAM
W 14 x 142 is used as a column having a length of 9 m. long. It is hinged at the r end and fixed at the lower end but there is a lateral bracing perpendicular to minor axis of the W section at a point 6 m. above the bottom support. It is assumed to be pinned connected at the bracing point. Using A 36 steel Fy 248 MPa the NSCP Specifications. E= 200000 MPa. Properties of W 14 x 142 A-26967.69 mm2 d=374.65 mm bf=393.70 mm tf-27.00 mm tw 17.27 mm Ix 695.11 x 106 mm4 Iy = 274.71 x 106 mm4 rx = 160.53 mm ry 100.84 mm 221 Assume: Kx=0.80 for 9 m. length KY 1.9 for the length on the upper support KY-0.80 for the length on the bottom support CIVIL ENGINEERING- STEEL DENON a) Compute the slenderness ratio along y-axis. b) Compute the slenderness ratio along x-axis. c) Compute the safe axial load
A 20-foot long column is pinned at the bottom and fixed against rotation but free to translate at the top. It must support a service dead load of 110 kips and a service live load of 110 kips. a. Select a W12 of A992 steel. Use the column load tables. 1. Use LRFD. 2. Use ASD. b. Select a W18 of A529 Grade 55 steel. Use the trial-and-error approach covered in Section 4.6. 1. Use LRFD. 2. Use ASD.
The W36 x 135 beam shown carries service loads shown (excluding weight). It has been decided to add a 10-meter steel column at point B to eliminate excessive deflection. If the column being added is fixed at the bottom and pinned at the top, design the column that can withstand as support (Use a recommended value for K. Evaluate using LRFD and ASD). a. Use WT18 section b. Use W36 section c. Using the section at (b), determine the dimension of the base plate if the foundation dimension will be 1500mm x 1500mm. Pp = 88 kN PL = 163 kN Wp = 21 kN/m WL = 58 kN/m C B 6 m 12 m
Give me answer fast
Q9
1. A one-bay one-story frame, shown in the Fig. 1, consist of a truss system. Two different types of connections are proposed for the 1s joint. Check the all requirements for tension. All dimensions are given in cm. M20 bolts with standard holes are used. S355 Structural Steel is used in all parts (F 355 MPa and F-490 MPa). 2 3 Lateral Load Please explain the solution, step by step! For example sketch the net areas show how to calculated! 4 5 An IPE beam is used to carry axial tension load (P) for the 4th member. a. Calculate the tensile strength (P) of the member according to AISC 360 LRFD and ASD. b. Determine the thickness (t) of the gusset plate according to max. tensile load calculated in part (a). 4,05 4,05 IPE360 P 26 Cross-sectional View Side View Top View
Design the member A-B to withstand the given loads P3 =12, W1=14 KN/m, P1 = 20 KN, P2 = 20 KN L = 7m, H1 = 4m H2 = 6m, P1 at L/3, P2 at 2L/3 notes choose proper material, all loads are unfactored Dead loads assume K= 0.7 P3 H2 A B HINGE W1 D P1 P2 H1 L HINGE C
Use A992 steel and select a W14 shape for an axially loaded column to meet the following specifications: The length is 22 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD. b. Use ASD.
Select a WT section for the compression member shown in Figure. The load is the total service load, with a live-to-dead load ratio of 2.5:1. Use Fy 5 50 ksi. a. Use LRFD. b. Use ASD 21' 175 k 1