As shown in the figure, members AC and BD are used to brace the pin-connected structure against a horizontal wind load of 10 kips based on ASCE 7- 16. Both of these members are assumed to be tension members and not resist any compression. For the load direction shown, member AC will resist the load in tension, and member BD will be unloaded. Select THREADED rods of ASTM A36 steel for these members. Use load and resistance factor design. a) Specify the diameter of the selected ASTM A36 THREADED rod

As shown in the figure, members AC and BD are used to brace the pin-connected structure against a horizontal wind load of 10 kips based on ASCE 7- 16. Both of these members are assumed to be tension members and not resist any compression. For the load direction shown, member AC will resist the load in tension, and member BD will be unloaded. Select THREADED rods of ASTM A36 steel for these members. Use load and resistance factor design. a) Specify the diameter of the selected ASTM A36 THREADED rod

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel used is A36, Fy = 248 MPa, Fu = 400 MPa. If the width of the tension plate is 210 mm, determine: a) The thickness of the plate based on NSCP 2015 ASD, bult used is M20. b) The thickness of plate based on NSCP 2015 LRFD. Bolt used is M20. 210 mm Tension Plate M20 bolts
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
From the Truss member shown, design all the tension members for ASD and LRFD, if the connection for the angle bars are shown. Use A36 STEEL. 100 mm 150 mm 2.5 m B SERVICE DEAD LOAD =300 KN SERVICE LIVE LOAD = 200 KN 2 m 2 m 2 m 2 m
A W14X120 is used as a tension member in atruss. The flanges of the member are connected to a gusset plate by 3/4 inch boltas shown below. Use A36 steel with Fy-36 ksi and Fu=58 ksi Determine the Yielding Capacity of the section based on LRFD (kips) Determine the Tensile Rupture capacity of the section based on LRFD Determine the Demand to Governing Capacity Ratio (based on yielding and rupture only) if the Demand load carried by the section are DL=200 kips LL=400 kips use LRFD Properties and Dimension Ag=35.30 in^2 x = 6.24 in ry= 3.74 in d=14.5 in tf=0.94 in bf=14.7 in tw=0.59 in k=1.54 d=14.5 Y k1=1.5 bf=14.7 tf-0.94 X -tw=0.59 H
A C130x10 tension member is welded to a plate as shown in the figure. The channel is of Grade 350W steel. The channel is welded on both sides with 110 mm long fillet weld. Assume the weld does not govern the capacity, calculate the factored tension resistance of the channel. The tension resistance is not governed by the plate. C130 XI0
Determine the smallest allowable diameter for a circular cross-sectional area of members BD, BE and CE of the truss shown. The working normal stresses are 2000 psi in tension and 1200 psi in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) 12 t 40 kips
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
SOLVE FOR1 HR
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
3.6-5 Choose a pipe to be used as a tension member to resist a service dead load of 10 kips and a service live load of 25 kips. The ends will be connected by welding completely around the circumference of the pipe. The length is 8 feet. a. Use LRFD. b. Use ASD.
A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 Emfr