8.5mSteel girder(A = 21,100 mm?)B-SteelcolumnProblem 1. The floor system of anapartment building consists of a100-mm-thick reinforced concrete100 mmconcrete slabD.2 at 3.6 m=7.2 mSteel floor beam(A = 11,800 mm2slab resting on three steel floorbeams, which in turn are supportedby two steel girders, as shown in the Figure. The areas of crosssection of the floor beams and the girders are 11,800 mm2 and21,100 mm2, respectively. Determine the dead loads acting on thebeam CD and the girder AE.

Answered: Image /qna-images/answer/ed05efc2-e128-4e3d-b867-188733c50641.jpg

Answered: (A = 21,10 1. The floor system of an t…

(A = 21,10 1. The floor system of an t building consists of a thick reinforced concrete ng on three steel floor hich in turn are supported Steel flo A = 11.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the tensile steel ratio for positive bending. 2. Determine the depth of the uniform rectangular stress block on the beam section at ultimate stage when subject to positive bending. 3. Determine the design moment capacity in kN•m of the beam in positive bending.
A concrete one-way slab has a total thickness of 120mm. The slab will be reinforced with 12 mm diameter bars with fy=275 MPa, fc'= 21 MPa. Determine the area of rebar in mm^2 if the total factored moment acting on 1m width of slab is 23 kN-m width of slab is 23 kN-m. Clear concrete cover is 20 mm.
The beam is loaded uniform deadload of 42 kN/m (including its own weight), and a uniform live load of 48 kN/m. Concrete strength fc' = 21 MPa and steel yield strength fy = 415 MPa, concrete cover is 65 mm from the centroid of the bars. Assume El to be constant. 320 mm 540 mm 7m 2m a. What is the uniform factored load on the beam in kN/m? b. What is the vertical reaction (factored) at B in KN? c. What is the maximum nominal moment can the beam carry if it is to be design as singly reinforced, in kN.m? d. What is the required tension steel area in mm2, at point of maximum positive moment? e. What is the required tension steel area in mm2, at point of maximum negative moment? f. Using simplified calculation, calculate the nominal shear strength provided by concrete near the fixed end, in KN? g. Using 10 mm W-stirrups with fyh = 275 MPa, what is the required stirrup spacing near the fixed end?
A TIMBER BLOCK “B x B” mm SQUARE IS REINFORCED ON OPPOSITE SIDES BY A “B” mm AND ‘t’ mm THICK STEEL PLATES. DETERMINE THE THICKNESS ‘t’ SO THAT THE ASSEMBLY WILL SUPPORT AN AXIAL LOAD OF 1000 KN WITHOUT EXCEEDING A MAXIMUM TIMBER STRESS OF 12 MPa OR A MAXIMUM STRESS IN STEEL OF 350 MPa. MODULUS OF ELASTICITY OF STEEL AND TIMBER ARE 210 GPa & 7 GPa RESPECTIVELY.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in negative bending.
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. 1. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only. 2. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.
Question 31 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the design moment capacity in kN∙m of the beam in negative bending. Write the answer in 2 decimal places only.
Situation #1: A reinforced concrete beam has a width of 300 mm and an overall depth of 550 mm. The beam is reinforced with five 25-mm diameter bottom bars and two 16-mm-diamter bars, both having fy = 345 MPa. Concrete strength fc' = 24 MPa. The centroid of the bars are located 65 mm from extreme concrete fibers. Unit weight of concrete = 23.5 kN/m3. The beam is simply supported over a span of 6 m and carries a superimposed deadload of 8 kN/m. Use NSCP 2010 1.1 What is the depth of compression block? 1.2 What is the stress of the compression steel? 1.3 What is the nominal capacity of the beam? 1.4 What safe uniformly distributed live load can the beam carry over its entire length? 1.5 Using the loads obtained from the previous questions, what is the required nominal shear strength of the beam at critical section near the support? 1.6 Using 10 mm U stirrups with fy = 275 MPa, what is the required stirrup spacing near the support.
Use USD method.
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D