A 20 mm diameter shaft of length 500 mm is fixed at one end. A torque, T is applied at its free end. The linear strain at surface of an angle of 45. from the axis is 4.0 x 10-3 calculate the torque. Take E =2.0 1011 and G=8.0X10¹0

A 20 mm diameter shaft of length 500 mm is fixed at one end. A torque, T is applied at its free end. The linear strain at surface of an angle of 45. from the axis is 4.0 x 10-3 calculate the torque. Take E =2.0 1011 and G=8.0X10¹0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @ 5 Hz when constant 120 KW is applied. Use the following: G(alum)=28 GPa, a=1.80 m, b=0.80m & L=2.60 m. Assumed that the angle of twist is constant. The torque "T1" developed at left fixed support at a is ___KN-m A 3.82 B 1.18 2.64 0.48 5.03 E
The bell crank is in equilibrium for the forces acting in rods (1) and (2). The bell crank is supported by a pin with a diameter of 14 mm at B that acts in single shear. The thickness of the bell crank is 7 mm. Assume a = 60 mm, b = 100 mm, F₁ = 1000 N, and 9 = 75°. Determine the average shear stress in pin B. Answer in MPa rounded-off to 2 decimal places. Bell crank dd your answer I saved 9:04:22 AM uestions Filter (6) b K First Previous Next > Last >
A cylindrical pressure vessel having a radius r = 14 in. and wall thickness t = 0.375 in. is subjected to internal pressure p = 375 psi. In addition, a torque T = 90 kip-ft acts at each end of the cylinder (see figure). (Assume that the structures behave linearly elastically and that the stresses caused by two or more loads may be superimposed to obtain the resultant stresses acting at a point. Consider both in-plane and out-of-plane shear stresses unless otherwise specified.) (a) Determine the maximum tensile stress omay and the maximum in-plane shear stress Tmay in the wall of the cylinder. (Enter the magnitudes in ksi.) o, = ksi Tmax ksi (b) If the allowable in-plane shear stress is 4.5 ksi, what is the maximum allowable torque T? (Enter the magnitude in kip-ft.) kip-ft (c) If T = 150 kip-ft and allowable in-plane shear and allowable normal stresses are 4.5 ksi and 11.5 ksi, respectively, what is the minimum required wall thickness (in inches)? in.
3. Solve the following problem The following shaft is subjected to three torsional moments expressed as a fraction of T. Determine the maximum value of the T if the allowable shear stress is Tallow 80 MPa. Draw the torsion (torque) diagram along the shaft for that value of T, and determine the relative angle of twist between sections A and C (use a shear modulus G = 26GPa). = diameter d 60mm Tallow 80MPa G = 26 GP₂ Req'd: allowable torque T angle of twist of A relative to C PAIC Torsion diagram 1.2m 1.2m
Help please!
05 A steel shaft ABC of 50 mm diameter as shown in figure is driven at A by a motor that transmits 50 kW to the shaft at 10 Hz. The gears at B and C remove 30 kW and 20 kW respectively. Compute the maximum shear stress in the shaft and the angle of twist between the ends A and C. (Take G= 80 GPa) Motor A 1.0 m-1.2 m 50 mm B C
Solve the Problem, Thanks
To determine the state of stress in a solid rod using the principle of superposition. A solid rod has a diameter of e = 50 mm and is subjected to the loading shown. Let a = 190 mm, b= 220 mm, c = 310 mm, d = 220 mm, and P = 3.0 kN. Take point A to be at the top of the circular cross-section. (Figure 1) Figure < 1 of 2 ▼ ▼ Part A - Moment about the x axis at A M₂ = As shown (Figure 2), a cut was made at A to determine the resultant internal loadings. Determine the moment about the x axis, M, Express your answer to three significant figures and include the appropriate units
Within few minutes
A circular shaft which has a diameter of 100 mm is subjected to torque of 5 kN-m. The shear stress in N/mm2, induced in the shaft would be A B D 160 TT 120 π 125 π 80 E TT
For the two-shaft shown below, rank each point (1, 2, 3, 4) on the cross-sectional areas in terms of shear stress. Both shafts are subjected to the same torque T. Shaft A has a radius of 4 cm. Shaft B is a hallow shaft that has an outer radius of 8 cm and inner radius of 5 cm. 4 1 2. 5 cm 8 cm 1 cm 4 cm Shaft A: solid shaft Shaft B: hallow shaft