A 2.5 inches diameter by 3.75 inches long and 360° bearing turns at 1,200 RPM and consumes 0.1 Hp in friction. Find the total load for the bearing if the film is at a temperature of 175°F (Viscosity = 0.000 001 03 lb sec/sq.in.), and using SAE 10 Oil with r/c = 1,000

Q: volumetric efficiency of the reciprocating pump that has a bore size of 350 mm and stroke of 400 mmm…

A:

Q: A radial plain bearing has a diameter of 60 mm and a width of 60 mm. Journal rotation speed 600 rpm;…

A:

Q: A full journal bearing has a shaft journal diameter of 25 mm with a unilateral tolerance of –0.01…

A: Write the given values using suitable variables. Here d signifies shaft diameter, tu signifies…

Q: e on a 6-in. full journal bearing is 5 intained at 160 °F with N = 300 rị ent of friction and the…

A: GIVEN:r=radius=3inl=length of bearing=1.2×6ns=revolution per sec=30060

Q: 8- If a liquid has an amount of viscosity (0.0048 poise) Calculate the sternum of the sternum…

A: Fluid Machinery

Q: 9.) What is the required diameter in meters of a cylindrical tank which has a length of 3 meters…

A: Note: As per the Bartleby guidelines, only one question can be answered at a time. Therefore,…

Q: Solve with the correct units 6. A square block weighing 1.1 kN and 250 mm on an edge slides down in…

A: GivenW=1.1kNa=250mm=0.250mθ=20ot=6μm=6×10-6mν=7mPa.s =7×10-3 Pa. s

Q: An equation for determining the friction factor developed by Colebrook is 1/√f =-0.869…

A: Write the expression of friction factor developed by Colebrook.   1f=-0.869lnεD3.7+2.523Re×f   Write…

Q: A mud sample in a rotational viscometer equipped with a standard torsion spring gives a dial reading…

A: Given data as per question Reading at  600 rev/min=46 Reading at 300 rev/min =28

Q: 2. An automobile and its load weigh 22.5 KN and the center of gravity is 0.60 m above ground level…

A: Given  , Weight of the car , W =22.5 KN Initial velocity of car , U = 96.5 Km/hr = 26.66m/s Final…

Q: Let the curve for and f for a 3-in. diameter x 6-in. long bearing be a through straight line passing…

A: Given, Load, W=1400lbs1lbs=4.448NW=1400lbs=6227.2NRpm, N=1000rpmFor the friction corresponding to…

Q: Question1: Calculate the load carrying capacity of a full journal bearing which uses SAE 10 oil…

A: Since you have asked multiple questions, we will solve one question for you. If you want any…

Q: A shaft of 100mm diameter rotates at 120 rad/sec in a bearing 150mm long. If the radial clearance is…

A:

Q: Lubricant temperature = 60°C Ambient temperature = 15°C Bearing pressure in pump = 1.2 MPa Heat…

A:

Q: A flat area 1.5x106mm² is pulled with a speed of 0.4m/s relative to another plate located at a…

A: Given data: A=1.5×106 mm2=159×10-6 m2du=0.4 m/sdy=0.15 mmμ=1 poise=0.1 Pa.s Need to determine the…

Q: The Pitot and piezometer tubes indicate the following total and static pressures: P1 = 112 kPa, P2 +…

A: Given data: Pressure P1=112 kPa Pressure P2+ρv222=240 kPa Need to determine the speed v1.

Q: 1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area…

A: Given:Distance between plates, y=0.05 mmvelocity of moving plate, v=1.15 m/sForce per unit area=3.2…

Q: A fix inclined-plane thrust bearing is designed to carry a total normal load of 50kN at optimum…

A: Given : W = 50 kN r0 = 100 mm ri = 50 mm N = 3600 rpm l/b =1 b = 40mm hi – h0 = 25 μm μd = 29 cP To…

Q: For a hydrodynamically lubricated bearing design. The following design data are given: Radial Load =…

A: Radial load W=1250 lbdshaft=1.75 in ordshaft=44.45 mmP=240 psiN=600 rpmLubricant SAE30 Oil at 160…

Q: A large manufacturer of air compressors is developing an air-cooled piston model and a water-cooled…

A: For both the models we can see that inital conditions before compression are same Now For the…

Q: ed with using an oil of specific gravity 0.8. Find the dynamic viscosity and kinematic viscosity of…

A:

Q: Find the friction factor: Diameter, D=50 cm velocity, v=1 m/s Kinematic Viscosity=1 mm2/s…

A:

Q: A shaft with a 25 mm radius is pushed at 300 mm/s inside a 25.5 mm radius bearing sleeve with a 230…

A:

Q: A tape, of width w = 25.40 mm is to be coated on both sides with a lubricant by drawing in through…

A:

Q: A certain six-cylinder engine has a 130.2 mm bore, a 127 mm stroke, and a clearance  volume of 0.119…

A:

Q: You are being asked to determine the heights in tubes B and C (relative to z=0) given the following…

A:

Q: A journal bearing supports a load of 12,000 N on a 150-mm diameter shaft running at 1500 rpm. The…

A: Diameter of the bearing (d) =150 mm = 0.15 m Load on the bearing (P) = 12,000 N Speed of the bearing…

Q: an oil drum of 500 mm diameter and 1.5 long is to be rolled across a footstep of 100 mm high.find…

A: Given Data: The diameter of the drum is, d=500 mm. The length of the rod is, l=1.5 m. The height of…

Q: A tape, of width w= 25.40 mm is to be coated on both sides with a lubricant by drawing in through…

A: Given Data Width of tape is : w=25.40 mm=0.0254 m Length of tape is : L=20 mm=0.02 m Thickness is :…

Q: Two parallel surfaces move relative to each other are separated by a gap of 0.375 in. The gap is…

A: Given Data: Two parallel surfaces having a gap dy=0.375 in Viscosity of Fluid μ=0.00431 lb-secin2…

Q: 5. A 12-in.-diameter circular plate is placed over a fixed bottom plate with a 0.1-in. gap between…

A:

Q: ibrication stable? Line of centers Journal Bushing -ho C= radial clearance

A: Solution