A 2.3-lb slider is propelled upward at A along the fixed curved bar which lies in a vertical plane. If the slider is observed to have a speed of 10.2 ft/sec as it passes position B, determine (a) the magnitude N of the force exerted by the fixed rod on the slider and (b) the rate v at which the speed of the slider is changing (positive if speeding up, negative if slowing down). Assume that friction is negligible. B 27! 2.9'

A 2.3-lb slider is propelled upward at A along the fixed curved bar which lies in a vertical plane. If the slider is observed to have a speed of 10.2 ft/sec as it passes position B, determine (a) the magnitude N of the force exerted by the fixed rod on the slider and (b) the rate v at which the speed of the slider is changing (positive if speeding up, negative if slowing down). Assume that friction is negligible. B 27! 2.9'

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8. The motor draws in the cable with an acceleration of 3 m/s2. The beam has a uniform mass of 20 kg/m , and the crate has a mass of 250 kg . Neglect the mass of the motor and pulleys.
A robot arm moves in the vertical plane so that the 0.14-kg cylinder P travels in a circle about point B, which is not moving. Know that arm BP starts from rest in a horizontal position and that the speed of Pincreases at a constant rate of 200 mm/s². 0.8 m Draw the free-body diagram of the cylinder P that is required to determine the force acting on the cylinder. (You must provide an answer before moving on to the next part.) 0.8 m P 1 I
A 1.6-lb slider is propelled upward at A along the fixed curved bar which lies in a vertical plane. If the slider is observed to have a speed of 11.5 ft/sec as it passes position B, determine (a) the magnitude N of the force exerted by the fixed rod on the slider and (b) the rate v at which the speed of the slider is changing (positive if speeding up, negative if slowing down). Assume that friction is negligible. 23 2.9' Answers: N = i Ib v= i ft/sec2
The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
A worker develops a tension T in the cable as he attempts to move the 48-kg cart up the 21° incline. Determine the resulting acceleration a of the cart if (a) T = 135 N and (b) T = 222 N. Neglect all friction, except that at the worker's feet. The acceleration a is positive if up the slope, negative if down the slope. 48 kg 15° Answers: 21 O (a) T = 135 N, (b) T = 222 N, a = a =
Dynamic Lecture: The 2 kg BC ring can only move left and right on the frictionless rigid arm. Ring BC is connected to springs with spring constants k = 300 N / m and k ′ = 200 N / m at points AB and CD. The unstretched length of both springs is 600 mm. Since it is known that the springs are not tensioned and starts from rest, find the velocity of the ring BC at the moment when the external force F is applied 200 mm.
Solve the following problem (NOTE: Use any reasonable DATA not given in the problem.)
1. A wood block of mass mw = 200 g is projected from the ground at a speed vo= 35 m/s and at an angle 0o = 50°. When at height h = 24 m the wood block was hit by a bullet of mass mb = 25 g which was moving at vb= 220 m/s and at an angle Ob = 70°. After the collision, the bullet embedded itself in the block and move together and land at point A on the ground. Then they move on the ground that has coefficient of kinetic friction uk = 0.5 and start to compress a horizontal spring at point B. The distance between point A and B is 18 m and the spring constant k = 3×10² N/m. Right end of the spring is fixed, and all motions are confined in x-y plane. Wood block + Bullet Bullet Wood A B block (a) Was the collision between the wood block and the bullet elastic or inelastic? Explain quantitively. (b) Find the maximum height from the ground the block with the bullet reached. (c) How far is point A from the launch point of the wood block? (d) Calculate the velocity at which the block-bullet…
2. Now consider the pulley problem shown below. In this problem, both blocks have mass m m m (a) At the instant shown, the block on the horizontal surface is moving to the right with speed v. At this instant, what is the velocity of the other block? (b) What is the acceleration of the block on the right?
A 22-lb body is traveling in a horizontal straight line with a velocity of 19.5 ft/sec when a horizontal force P is applied to it at right angles to the initial direction of motion. If P varies according to the accompanying graph, remains constant in direction, and is the only force acting on the body in its plane of motion, find the magnitude of the velocity of the body when t = 3.2 sec and the angle which the velocity makes with the direction of P. P, lb 3.4 A 1.7 0 0 1.6 2.4 3.2 t, sec Answers: V = 0= i i 1 1 ft/sec O
2. A block travels past point A with a speed of 8 m/s along a smooth surface until it reaches a rough surface of length L=20 m and a coefficient of kinetic friction of 0.8. If the height h₁ = 8 m, and h₂ = 3 m. Determine (A) the speed of the block at point B (B) whether the speed at point C (C) reaches point D. If so, what is the speed at point D, if not, how far is the rough surface that cross the beam?
I need the answer as soon as possible