A 2-wire d.c. distributor cableAB is 2 km long and suppliesloads of 100A, 150A,200A and50A situated 500 m, 1000 m,1600 m and 2000 m from thefeeding point A. Eachconductor has a resistance of0-010 per 1000 m. the p.d. ateach load point if a p.d. of 300V is maintained at point A is: *O no one of the answers (a, b & c)VA=300V; VC=289V; VD=285V;VE=281V; VB=793VVA=300V; VC=270V; VD=265V;VE=260V; VB=255VVA=300V; VC=295V; VD=291V;VE=288V; VB=287.6V

Given: Resistance/conductivity/1000m=0.01ΩLoop resistance, r=2×r'(given…

A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0-01Q per 1000 m. the p.d. at each load point if a p.d. of 300 Vis maintained at point A is: * no one of the answers (a, b & c) VA=300V; VC=289V; VD=285V; VE=281V; VB=793V VA=300V; VC=270V; VD=265V; VE=260V; VB=255V VA=300V; VC=295V; VD=291V; 1O VE=288V; VB=287.6V

A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0-01Q per 1000 m. the p.d. at each load point if a p.d. of 300 Vis maintained at point A is: * no one of the answers (a, b & c) VA=300V; VC=289V; VD=285V; VE=281V; VB=793V VA=300V; VC=270V; VD=265V; VE=260V; VB=255V VA=300V; VC=295V; VD=291V; 1O VE=288V; VB=287.6V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

One advantages of load balancing is that each phase conductor carries the ? current value
Help with this third one please
A two-wire DC splitter of 1Km length and resistance of each conductor (m/00030.0) and feeds the loads as shown in the augmented form: 1. Minimum voltage point on the conductor 2. The voltage at each load point 400V 200m 300m 400m 100m 80A 60A 10A SOA
The minimum size raceway for the following feeder conductor is: a. Three, 250kcmil conductor with XHHW insulation b.One3/0 AWG conductor with XHHW Insulation c. One, 4AWG Conductor with XHHW INSULATION
In a 3-phase 4-wire system, the currents in R, Y and B lines under abnormal conditions of loading are 11=100 A, (angle 30 degree), 12=300 A (angle 300 degree), 13=100 A (angle of 180 degree). The current in the neutral wire is: Select one: O a. None of above Ob. 13 A O c. 51 A O d. 150 A O e. 250 A
Power system
Primary EL 600 Volts EP = IL |||| IP = Primary Secondary Secondary EL = EP = 277 Volts IL = IP = Ratio = VA 125 KVA = 1. What size THW copper conductors are needed for the primary conductors? 2. What size THW copper conductors are needed for the secondary conductors? 3. What size Overcurrent protection is needed for the primary conductors?
3. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60 A, 40 A and 30 A are tapped at distance of 100 m, 250 m, 350 m and 400 m from end A respectively. If the X- section of conductor be 1 cm and specific resistance of the material of the conductor is 1-7 u 2 cm, determine the minimum consumer voltage. 1245-07 VI
Two wire systems have the voltage at the supply end maintained at 500 V. The line is 4 km long. If the full-load current is 15 A, what must be the booster voltage and output in order that the far end voltage may also be 500 V. The resistance of the cable is 0.5 ohm/km.
Please solve in 15 min
3. A 250 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rate of 0-8 A per metre. The resistance of each conductor is 0.0002 2 per metre. Find the necessary voltage at the feeding point to maintain 250 V at the far end of the distributor. [260 V]
These are laminated steel core containing current-carrying copper wires; and in general if it is the stationary part, it is called as