A 2 percent uranium oxide slurry (2 lb UO2 / 100 lb H2O) flows into a 100 gallon tank at the rate of 2 gallons per minute. The tank initially contains 500 lb of H20 and no UO2. The slurry is well mixed and flows out at the same rate at which it enters. Find the concentration of slurry in the tank at the end of one hour.

A 2 percent uranium oxide slurry (2 lb UO2 / 100 lb H2O) flows into a 100 gallon tank at the rate of 2 gallons per minute. The tank initially contains 500 lb of H20 and no UO2. The slurry is well mixed and flows out at the same rate at which it enters. Find the concentration of slurry in the tank at the end of one hour.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

None
In any manufacturing process, reaction monitoring ensures that a chemical reaction proceeds as expected. Table 1 shows the monitoring data for the formation of chlorohexane, collected using a technique called gas chromatography. Note that the concentrations of the chlorohexane solutions are given in millimoles per litre (mmol l–1). The abbreviation mM (millimolar) is frequently used. Plot a graph of the data in Table 1. The graph should be drawn on graph paper or use fine grid if it’s drawn on Excel. Elapsed Time/Hours Concentration of Chlorohexane/mM 0 0 2 40 4 65 6 80 8 90 10 95 12 99
What is the concentration of FeSCN2+ in each standard solution? (Show ALL calculations for each solution) Stock Solution of the concentration of FeSCN^2+ is 0.00200 M
K2CO3 (aq)+ CaCl2 (aq)→ CaCO3 (s) + 2KCl (aq) Data Sheet Table 1: Data and Observations Material Mass CaCl2 2.0g K2CO3 2.5g Filter Paper 1.6g Watch Glass 35.8g Filter Paper + Watch Glass + Precipitate 38.9 Precipitate 1.5g Table 2: Mass of CaCl2 after 24 Hours Initial Observations 24 hour Observation Weigh Boat Mass of Weigh Boat 0.5g Mass of Weigh Boat 0.5g CaCl2 2.0g Mass of CaCl2 2.4g Mass of CaCl2 Calculate the theoretical yield of the solid precipitate. Then use that to calculate the percent yield of the solid precipitate.
1. The following data are from total and volatile solids tests on a wastewater. Calculate the total and volatile solids concentration in mg/L. Weight of empty dish = 68.942 g Weight of dish + dry solids = 69.053 g Weight of dish + ignited solids = 69.003 g Volume of wastewater sample = 100 mL
A water quality monitoring found that local bayou contains 8.72x10-4 % (wt/wt) nitrate ion ( MW = 62.01 g/mol). Yet the EPA standard for the nitrate content in a natural water body is 1.613x10-4 M or lower. Is the mentioned bayou water in that location acceptable from the EPA standard ? List your calculation steps (Density of bayou water is 1.0 g/mL).
A compound “X” is regulated by health Canada at 2 ug/L in drinking water (maximum allowable concentration). What will be the minimum cut-off level of your analytical method to analyze that compound “X”? How do you determine the cut-off level of your method?
Six 50.0 ml volumetric flask 1 through 6 are labeled. 10.00 ml of 2.00 x 10-1 M Fe(NO3)3 solution was then pipet into each volumetric flask. A 1.00,2.00,3.00,4.00 and 5.00ml of 2.00 x 10-3M NaSCN solution was then pipetted to flask 2 through 6 respectively. A sufficient amount of 0.10 M nitric acid was then added to each flask to make each a total volume of 50.00ml. Hint M1V1=M2V2 a)what would be the concentration of Fe(NO3)3 in 0.10M HNO3? b)what would be the concentration of NaSCN in 0.10M HNO3?
A 25mL volumetric pipet is used to deliver a sample of the stock solution marked “0.6000M X2SO4” into a 100mL volumetric flask. Distilled water is added to the flask until it is about 3/4thfull, the solution is mixed well, then more water is added to fill it up to the calibration mark, then it is mixed again. Calculate the concentration of X+ion in the dilute solution made above.
A student prepares a 3.2M aqueous solution of benzoic acid (C,H,CO,H). Calculate the fraction of benzoic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource. Round your answer to 2 significant digits. | % x10
You measure 15.0 mL of the H2C2O4 solution with a 100-mL graduated cylinder and add it to a 125-mL Erlenmeyer flask. Then you add two drops of the indicator, phenolphthalein, to the oxalic acid solution in the flask. You dispense the NaOH solution from the buret into the flask (while swirling the flask) until you reach the endpoint. At the endpoint, the solution in the flask turns light pink. You repeat the titration two additional times for a total of three trials. H2C2O4 (aq) + 2 NaOH (aq) --> Na2C2O4 (aq) + 2 H2O (l) (I) (II) (III) Volume of H2C2O4 used 15.00 mL 15.00 mL 15.00 mL how many Moles H2C2O4 are used in each trial?
Using recrystallization techniques, a student attempts to purify 0.50 g of compound H. Based on the solubility of H in the chosen solvent at collection temperature, the maximum percent recovery is 82%. The student obtains 0.396 g of purified crystals. What is their percent recovery? Group of answer choices 41% 64% 79% 82% 97% none of these