A 2-m-high, 3-m-wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridge at B. The container is filled with 3-m-high Engine oil SAE 10W-30 (SG = 0.875) a) Determine the hydrostatic force exerted on the gate b) Determine the location of the center of pressure c) Describe the force exerted by the oil on the gate d) What does the center of pressure mean? And why is it always located below the centroid of the submerged surfaces? e) Draw a sketch showing the location of the centroid and the center of pressure

A 2-m-high, 3-m-wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridge at B. The container is filled with 3-m-high Engine oil SAE 10W-30 (SG = 0.875) a) Determine the hydrostatic force exerted on the gate b) Determine the location of the center of pressure c) Describe the force exerted by the oil on the gate d) What does the center of pressure mean? And why is it always located below the centroid of the submerged surfaces? e) Draw a sketch showing the location of the centroid and the center of pressure

Name: Task (1)A 2-m-high, 3-m-wide rectangular gate is hinged at the top ed
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Task (1)A 2-m-high, 3-m-wide rectangular gate is hinged at the top edge at A and is restrained by a fixed ridgeat B. The container is filled with 3-m-high Engine oil SAE 10W-30 (SG = 0.875)a) Determine the hydrostatic force exerted on the gateb) Det

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylinder with a radius of r=1 m is hinged at location A. It is used as a gate to block water in the reservoir with H=6 m a) Determine the horizontal and vertical components of the resultant hydrostatic pressure force acting on the curved surface AB per unit lentgh and its direction. b) For this cylindirical gate, what is the required weight per unit length, to open automatically at H=6 m. water A
A 10000 litre water tank is placed on a building roof and filled to capacity. The empty tank has a mass of 550kg. It is supported on 4 feet, each of which is a 300 x 300 mm steel plate. What is the pressure exerted by each plate, in Pa? (Round your answer to 2 significant figures)
side the cylinder. (123.35kPa) Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the gage is 80kPa, determine the distance between the two fluid levels of the manometer 1.9 if the fluid is (a) mercury (p-13600kg/m') or is (b) water (p=1000kg/m). 1 10 The level of the water in an enelosed water
The bottom corner of a water tank that is 3 m wide (into the page) is constructed with a flat panel at an angle of 45° as shown in the figure below. The panel in question is shown as a heavy line. Note that water has a density of 1000 kg/m3. Determine: 2a) The magnitude of the total resultant force acting on the panel, FR 2b) The depth of below the water surface at which the resultant force vector acts on the panel, d
QUESTION 1 Determine the resultant hydrostatic force on the 1 m square door shown in the figure below, and the force F required to open the door. P = 0.05 MN/m² Po Gas 2 m F -Door -hinge T Water Gas Mercury- Figure 1 500 mm
A cylindrical steel container 8m high and 3m in diameter is reinforced with two hoops a meter from each end. If the contained liquid is water, determine the: a) total hydrostatic force and normal force acting on the wall of the tank b) tension of hoop at the bottom and tension of hoop at the top c) with an allowable stress of 0.12 GPa, compute the thickness of the steel required.
(c) Determine the magnitude and location of the resultant force acting on the vertical wall shown using pressure prism concept (width = 1.0 m). What is the limitation of using this concept? Patm 1.0 m Oil (0.9) Water (1.0) 1.5 m
4. A 3-m-long and 1-m-wide rectangular gate AB is hinged at point A. The gage reads -110 mmHg while the right tank is filled -110 mmHg with oil. Determine the horizontal hydrostatic force at point B (FB) that is required to be applied to keep the gate Water closed. Assume that the density of water and oil are 1000 kg/m3 and 750 kg/m³, 8 m A respectively. Oil 3 m FB B