A 18 nC charge is uniformly distributed over a spherical shell r = 8 cm and a -6 nC charge is uniformly distributed over another spherical shell r = 10 cm. a) ) Find the electric filed intensity E where r< 8 cm o} Find the electric filed intensity E where 8 cm 10 cm d) (:.\Calculate VAB if A = (9, x/2, n) and B = (11, 7/2, x) e) (i Find the work done in transforming a 12 nC charge from B to A.

A 18 nC charge is uniformly distributed over a spherical shell r = 8 cm and a -6 nC charge is uniformly distributed over another spherical shell r = 10 cm. a) ) Find the electric filed intensity E where r< 8 cm o} Find the electric filed intensity E where 8 cm 10 cm d) (:.\Calculate VAB if A = (9, x/2, n) and B = (11, 7/2, x) e) (i Find the work done in transforming a 12 nC charge from B to A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Need answer in 30 minutes
2. The electric field at a point P 4.5 cm away from a point charge has a magnitude of 3.75 x 105 N/C and points radially inward toward the charge. Find the electric potential at point P.
The parallel plates of an isolated charged capacitor are 1 mm apart and the potential difference across them is V. The plates are now separated to 3 mm (while the charge on them is remained constant) and a slab of dielectric material is inserted, filling the space between the plates. The potential difference across the capacitor is now Ve/2. Find the dielectric constant K.
d) A regulator as shown in Figure 4 has an input voltage, Vs 12 V. The duty cycle, k = 0.35 and the switching frequency is 30 kHz. It also has an inductance, L= 200 µH, filter capacitance, C = 440 µF. The average load current, la = 1.25 A. Determine the; i. average output voltage, Va. ii. peak-to-peak output ripple voltage, AVc. iii. peak-to-peak output ripple current of inductor, AI. iv. peak current of the transistor, Ip. v. critical values of L and C. vi. critical values of L and C if Vs is increased to 14 V. Estimate the change in percentage for the critical values of L and C. V, Load V V G Figure 4
A) Explain briefly various theories of breakdown in liquid dielectrics. B) What are the requirements of a sphere gap for measurement of high voltages? Discuss the advantages and disadvantages of sphere gap for measurements. C) Determine the Townsend's first ionization coefficient if a steady current of 500 µA flows through the plane electrode separated by a distance of 0.4cm when a voltage of 10 kV is applied. A current of 25 µA flows when the distance of separation is reduced to 0.1 cm and the field is kept constant at the previous value. Find also the value of y if the breakdown took place when the gap distance was changed to 0.7 cm.
Electrical Engineering - High voltage system EENG451 Please solve the question quickly
The magnetic field of a wave propagating through a certain nonmagnetic material in the negative z direction has an amplitude of 45mAlm and a frequency of 10Š Hz. If the wave is polarized on the positive x direction and the phase velocity of the wave is 10 m/s. Assume the initial phase is 30°. Find the relative permittivity of the material. Select one: O a. The relative permittivity of the material = 1 O b. The relative permittivity of the material = V3 O c. The relative permittivity of the material = 0 O d. The relative permittivity of the material = 3 O e. The relative permittivity of the material = 9 %3D
solve within 30 minutes for upvote
4-) Between parallel plates when two conductive metal plates with an area of 0 cm are separated from each other by 10 mm, a-) Determine the capacitance of the empty condenser run C. b-) Find the maximum amount of load to carry when the capacity r is empty. e-) What is the capacity of the newly formed system and the maximum load the capacity run will carry when mica with a capacity re dielectric constant k 8 is placed? 2/3 Ç-)After loading the capacitance nC, when the external voltage is removed and mica and mm sine nylon (keaytan=3) are placed in 3mm, find the final V and C values. boşluk Sum 2mm
1) Find E elements : everguhire - You do not need to dorive Ē for individuol Infinite Plates corrying uniform surfoce charge densities to. O dapasited uniformly on the surfuce of a sphenical shell of radius R.
B) The permittivity of a solid insulator is 5.6 and loss angle is 0.5 degree. If the insulator is subjected to an altemating field of 6 MV/m, at a frequency of 60 Hz, calculate the dielectric losses.
Date:. A 5nc foint chabge is located at Rint (x=o; Y=5; Z=2). An infnite sheet of change with teface charge denity donc/ma is berent at Y=do plene. Find uhese ?s Befo, the foint in Caterian co-ordimtes uhexe Ē cs Befo.