A 160x100x12 angular section is welded to a column's flange. The angle is A36 steel with Fy-248 MPa. The weld is EB0 electrode with Fu-550 MPa The centoidof the angle measured along its long leg is y-55 mm. See figure STMMI 56.Fig. STMMJ S6Which of the following most nearly gives the value of atO 124.37 mmO 11209 eO 121.50 mnO 118.63 mm

Answered: Image /qna-images/answer/101c62c0-9f29-4365-aa44-0cbe547efbd9.jpg

A 160x100x12 angular section is welded to a column's flange. The angle is A36 steel with Fy-248 MPa. The weld is EB0 electrode with Fa-550 MP The cenoid of the angle measured along its long leg is y-55 mm. See figure STMMI S6. Fig. STMMJ Which of the following most nearly gives the value of a O 12437 mm O 11289 en O 12150 mem O 118.63 mm

A 160x100x12 angular section is welded to a column's flange. The angle is A36 steel with Fy-248 MPa. The weld is EB0 electrode with Fa-550 MP The cenoid of the angle measured along its long leg is y-55 mm. See figure STMMI S6. Fig. STMMJ Which of the following most nearly gives the value of a O 12437 mm O 11289 en O 12150 mem O 118.63 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3.9 The compound shaft consists of bronze and steel segments, both having 120-mm diameters. If the torque T causes a maximum shear stress of 100 MPa in the bronze segment, determine the angle of rotation of the free end. Use G = 83 GPa for steel and G = 35 GPa for bronze.
Situation 4: The lap splice shown will develop a full strength as shown in the figure. Using E70 electrodes. The width of the plate is 50 mm and the thickness is 12 mm. Use Fy = 248 MPa T+ T4 O 29 mm O 30 mm 1. Which of the following nearly gives the diameter of the slot weld using the LRFD method. O 27 mm E70 O 28 mm T T
rectanqular seetion with width bz250 and depth h= 500mm is to carcry a A m %3D design bending moment M= 260KN•M, The conerete is of greade e30 and the tensile steel is of HRB400. The tension reinforzce. ment A, is requined.
IADC classification (4-1-4-T) refers to what kind of a bit? IADC classification (D-7-1- 4) refers to what kind of a bit?
Problem-7c.
Solve for joint @ A & C / AC
Find the stress in each rods. The 300 mm x 300 mm santrir m 2 m P-30 kN Steel L-0.5m E-200 GP A-500 m 1.5m Bronze L-2m E-70 GPa A-300 mm²
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 32-in.-long bronze [E = 13700 ksi] bar with a cross-sectional area of 1.29 in.2. Bar (2) is a 48-in.-long aluminum alloy [E = 10300 ksi] bar with a cross-sectional area of 2.19 in.2. Assume L1=32 in., L2=48 in., a=25 in., b=57 in., and c=15 in. Both bars are unstressed before the load P is applied. If a concentrated load of P = 26 kips is applied to the rigid bar at D, determine:(a) the normal stresses σ1, σ2 in bars (1) and (2).(b) the downward deflection vD of point D on the rigid bar.
CLO 1: For concentric rows of bolts in a coupling connection, the shear deformations in the bolts is proportional to the: O modulus of rigidity O diameter of bolt circle O radial distances O number of bolts