A 1600 Ik crate is supported by three cables as shown. Given UAB = -0.48î + 0.8ĵ – 0.36k, UAC = 0.0î + 0.8824ĵ + 0.4706k and ūAD = 0.5195î + 0.7792j – 0.3507k. Determine the equilibrium equation for the y-direction. Hint: watch coordinate system. 36 in. 0.8FAB + .8824FAC + 0.7792FAD – 1600 = 0 a. 40 in. b. -0.48FAB + 0.8FAB - 0.36FAB = 0 32 in. -0.48FAB + 0.0FAC + .5195FAD – 1600 = 0 C. 27 in- d. -0.36FAB + 0.4706FAC – 0.3507FAD – 1600 = 0 -0.36FAB + 0.4706FAC – 0.3507FAD = o е. 60 in.

Q: justt using the rule attached plss i need her all sloving

A: Based on the information you've provided and the image you sent, I can help you with the heat…

Q: 3. The loop closure equation for the offset slider-crank mechanism, shown below, driven by the…

A: Solution: Given Data: RC=RA+RBA+RCBRA=0.5 inθ2=40o   To Find: (a) θ3(b) RC

Q: Design a four bar linkage to generate the function y=x²-1 for values of x between 1 and 5. Use…

A: To solve this problem, we need to design a four-bar linkage that generates the function  the for…

Q: 3) A linkage has the following link lengths: O3A=3", AB= 8", O.B= 6", 0,0= 7". vi. Find out if the…

A: vi. It is satisfying grashof law, hence the given linkage is grashof mechanism. vii. When O2A is…

Q: The figure shows a linkage in one position. What is the instantaneous acceleration of point Pif the…

A:

Q: B W AB a b. A 0 = 45° 30°

A: Solution 1&2 In this step we find velocity:-

Q: Which of the following is the correct position vector loop equation for the linkage below? ONT +7…

A:

Q: Water with a viscosity of p=0.031 kg/m.s and density =1000 kg/m is to be siphoned through a tube 30…

A: GIVEN :- viscocity of water : μ=0.031kg/m.sdiameter of tube : D=1.5 mmdensity of water :…

Q: Consider the physical diagram below of a solid cylinder mass M that remains stationary on a slope…

A: Solution (a): Given Data:   To Find: Whether the given Free body diagram is correct or not.

Q: For the following mechanism, Given: . • Lengths: O₂A=4 in., O;B-8 in, BC=5 in., O₂O3-4 in. and…

A: “Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 9. Given the two-link revolute robot arm with L₁= 8 and L₂= 6, 01-35°, 0₂-20° find points Px and Py…

A: Given that :                         L1= 8                          L2= 6                         To…

Q: 5-The cables and loading are shown in the figure. If a is 75 degree and P =400 N. Find the tension…

A:

Q: Which of the following is the correct velocity vector equation for the linkage below? DA B. je D. 2e…

A:

Q: No software is required. I just need a explaintion of what is happening to this truss.

A: The figure shows the translation or the movement of the truss with respect to its original position.…

Q: Problem 3 Two consecutive frames describe the old and new T₂ positions and orientations of the end…

A: We have to find out the differential motion

Q: The transformation of position from polar to Cartesian coordinates is given by: x=rcose y=rsin 0…

A:

Q: A general inverted slider crank linkage has the following: The link lengths are link 2 = 5, link 4 =…

A:

Q: For the quick-return mechanism (at the instant shown): = 7/6 rad = -0.2 rad/s $=0 Perform a complete…

A: Given data;Initial angle of the crank ; Angular velocity of the crank ; Angular acceleration of the…

Q: I want to explain where the numbers 6.2772 and -1.274 come from(are marked in red) just calculation…

A: Based on the information provided in the image and your previous explanations, here's a breakdown of…

Q: The dingram Shows mass On 4uo ro tors in planes. B and c. Calculate The masses to be added On the…

A: Given:- mB=5kg mC=3 kg Radius=40mm Radius of mB=20mm Radius of mC=50mm AB=80mm BC=70mm CD=100mm

Q: 7. Given the two-link revolute robot arm with L₁= 12" and L2 = 8", 01= 45⁰, 02= -30°, find the end…

A: To solve this problem, we need to find the end-effector position (Px,Py) of the two-link revolver…

Q: Graph about the imagen

A: The given equation appears to involve Dirac delta functions, denoted as δt. The equation is: To…

Q: osition Analysis of the crank-slider linkage. The link length and offset for a fourbar…

A:

Q: A6.1: The linkage shown here has 02 62° in the local x'y' coordinate system. The angle between the X…

A: Draw the linkage for the scaleCompute constant by using the following formula:Here, is length of…

Q: Suppose that the coordinate frame 0₁x₁₁Z₁ is obtained from the coordinate frame ooxoyoZo by a…

A: The solution uses the formula for the rotation matrix about the x-axis, which is a special case of…

Q: The device shown in figure below can be analyzed as a pin-jointed fourbar mechanism in series with a…

A: The angle made by the link OC with the horizontal axis, The length of the link AB, The length of the…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.