A 16-pile group has to be arranged in the form of a square in soft clay with uniform spacing. Neglecting end bearing, the optimum value of spacing of the piles in terms of the pile diameter (d) is [Assume shear mobilisation factor = 0.6.] %3D

A 16-pile group has to be arranged in the form of a square in soft clay with uniform spacing. Neglecting end bearing, the optimum value of spacing of the piles in terms of the pile diameter (d) is [Assume shear mobilisation factor = 0.6.] %3D

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter9: Pile Foundations

Section: Chapter Questions

Problem 9.2P: Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through...

See similar textbooks

Similar questions

A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the allowable group pile capacity based on individual pile failure using a factor of safety of 3.
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, ơ'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225KN/m? At 12m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 300KN/m? 7m 5m Clay 3 10m Unit weight = 18KN/m Friction angle = 0 degree 2 Cohesion = 100KN/m Figure 1: Pile system
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425kN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 150kN/m? At 10m, eo = 0.55, Cc = 0.32, Cs = 0.09, o'o = 225kN/m2 %3D At 12m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 300KN/m2 %3D 7m 5m Clay 3 10m Unit weight = 18KN/m %3D Friction angle = 0 degree 2 Cohesion = 100KN/m
Check the total settlement of a group of pile as shown in Figure 1. The total allowable settlement is set not exceed 3% of the pile diameter and the overconsolidated ratio (OCR) of the clay is more than 1. The groundwater table is located 15m beneath the ground level. The diameter of the pile, b is 0.5m and the spacing between piles, s is 2m.The pile group is subjected to foundation load of 5425KN. The laboratory testing data for the soil samples taken are as follows: At 5m, eo = 0.55, Cc = 0.32, C, = 0.09, ơ'o = 150KN/m? At 10m, eo = 0.55, Cc = 0.32, C; = 0.09, o'o = 225KN/m? At 12m, e, = 0.55, Cc = 0.32, C, = 0.09, oo = 300KN/m? 7m 5m Clay 10m Unit weight = 18kN/m Friction angle = 0 degree Cohesion = 100KN/m
A nine pile group consists of 0.30m diameter friction concrete piles 12m long. The piles are driven into clay having an unconfined compressive strength of 180kPa and the unit weight of clay is 18kN/m3. The spacing of piles is 0.75m center to center. Assuming a bearing capacity factor of Nc = 9, a= 1.0. Which of the following most nearly gives the minimum pile spacing in order to achieve 100% efficiency?
Steel pipe piles are to be used as friction piles (i.e., pile capacity is from shaft resistance only) in an area where a deep deposit of normally consolidated clay exists. The soil unit weight is 17kN/m3, with shear strength cohesion cu equal to 45 kPa. Using the total stress α-method, determine the design axial capacity due to shaft resistance for a pile diameter of 0.30 m and an embedded length of 10 m. Apply a factor of safety of 2.75.
Please solve it complete in one hour
A 0.5 x 0.5m square concrete pile is to be driven in a homogeneous clayey soil having undrained shear strength, cu = 50 kPa and unit weight, g = 18 kN/m². The design capacity of the pile is 500 kN. The adhesion factor a is given as 0.75. The length of the pile required for the above design load with a factor of safety of 2.0 is..
Refer to the pile shown in Figure P9.1. Estimate the side resistance Qs by Using Eqs. (9.40) through (9.42). Use K = 1.5 and Coyle and Castello’s method [Eq. (9.44)]
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Determine the maximum load that can be allowed on the 450 mm diameter pile shown in Figure P12.9, with a factor of safety of 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load.
Consider a 500 mm diameter pile having a length of 18 m in a clay. Given: γ = 20.0 kN/m3 and cu = 60 kN/m2. Determine the maximum allowable load (Qall) with FS = 3. Use the α method and Table 12.11 for determining the skin friction and Eq. (12.20) for determining the point load. Allow a factor of safety of 3. What percentage of the ultimate load is being carried by the pile shaft? Is it a friction pile?