A 150mmø pipe having a total length of 102m carries a discharge of 60liters per second as shown in the figure. The minor loss coefficients for the entrance, elbows and globe valve are 0.50, 0.90 each and 10 respectively. If the friction factor f=0.005. 150 mm e ciean cast iron pipe 12 m Globe valve

A 150mmø pipe having a total length of 102m carries a discharge of 60liters per second as shown in the figure. The minor loss coefficients for the entrance, elbows and globe valve are 0.50, 0.90 each and 10 respectively. If the friction factor f=0.005. 150 mm e ciean cast iron pipe 12 m Globe valve

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the head loss in 2000 ft of 14-in diameter cast iron pipe at a flow rate of 1000 gpm. Use f = 0.025 for the pipe material.
What level h (m) must be maintained to keep the Reynold number at 1600 through the commercial-steel pipe? The total head loss hL=D20.8 m. Water (viscosity of 0.01 kg/m.s and density of 1000 kg/m3) water d=2 mm -45 m
Prove that the coefficient of friction for Hagen Poiseuille flow in a cylindrical pipe is equal to Cf= 16/Re
Three parallel pipes connected at the two ends have flow-rates Q₁, Q₂ and Q3 respectively, and the corresponding frictional head losses are hL₁, h₁2 and h13 respectively. The correct expressions for total flow rate (Q) and frictional head loss across the two ends (h₁) are (A) Q = Q₁ + Q₂ + Q3; h₁ h₁1 + hL2 + hL3 (B) Q = Q1 + Q2 + Q3; hL=hL1 = hL2=hL3 (C) Q = Q₁ Q₂ = Q3; h₁ = hL1 + hL2 + hL3 = = (D) Q = Q₁ Q2 Q3; h₁ h1 = hL2 = hL3 = = =
Hurry up plz
1
solve the problem below
State clearly your assumptions in your solution sheet
A 5 cm diameter potable water line is to be run through a maintenance room in a commercial building. Three possible layouts for the galvanized iron water line are proposed as shown in the figure. The bends are conventional threaded fittings. Select the option that minimizes losses and determine the pressure drop for a flow of 350 L/min. For the elbo losses use, hℓm =
The flow rate between tank A and tank B shown in the figure will decrease by 30% by adhering a second pipe that goes from point C to tank B. If the surface elevation of tank A is 25 ft higher than that of tank B, determine the diameter, D, of the second pipe. Despise lost minor and assume that the friction factor is 0.02.
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
D ¶ L The water in a large tank exits through a horizontal circular pipe of diameter D=0.01m and length L=62m. The centre of the exit of the pipe is h=1.4m below the water surface. We can assume that the flow entrance to the pipe is smooth so that there are no minor losses. The flow in the pipe is laminar, the friction factor can be assumed constant and can be found from fp = 64/Rep where the Reynolds number is based on the pipe diameter and mean flow speed in the pipe. Taking frictional losses into account, solve the resulting quadratic equation to calculate the speed of the flow out of the pipe. Give your answer in m/s to 2 decimal places. Use: kinematic viscosity given by v=0.00000114 m²/s density of water given by 1000 kg/m³ acceleration due to gravity of 9.81 m/s²