A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, p = 0.038 N-s/m²) from one tank to another (submerged discharge) where the difference in elevation of the free liquid surfaces is 2 m (Fig. P8.69). The pipe entrance is flush, and there is a fully-open gate valve in the line. Using only a basic scientific calculator, find the diameter theoretically required. (Hint: It may be easier to try for D than forf in this case.) A basic scientific calculator is here defined to be one that is not programmable and does not have automatic equation solving capabilities. Az Valve Le.Q Flush Figure P8.69

A 150-m-long commercial steel pipe is to convey 30 L/s of oil (s = 0.9, p = 0.038 N-s/m²) from one tank to another (submerged discharge) where the difference in elevation of the free liquid surfaces is 2 m (Fig. P8.69). The pipe entrance is flush, and there is a fully-open gate valve in the line. Using only a basic scientific calculator, find the diameter theoretically required. (Hint: It may be easier to try for D than forf in this case.) A basic scientific calculator is here defined to be one that is not programmable and does not have automatic equation solving capabilities. Az Valve Le.Q Flush Figure P8.69

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The system shown is in a vertical plane and the fluid has a relative density of 0.80. The pressure at point 1 is 260kPa, and the flow rate is 0.090 m3/s. Determine the reactions at the support at A.
The piping of the circuit in Figure is modified as follows. First, the pipeline from the upper discharge port of the directional control valve is connected to the rod end of the cylinder. Then the pipeline from the lower discharge port of the directional control valve is connected to the blank end of the cylinder. What effect does this have on the minimum flow capacity of the return line filter?
2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) 2 (ø - 250mm) 0.3m oil (as2) 0.8m - glycerin (1.86)
height of water the pressure intensity : () at the interface of the two liquids, and (ii) at the bottom of the tank. [Ans. () 1.57 N/cm", (il) 3.04 N/em 6. An open tank contains water upto a depth of 1.5 m and above it an oil of sp. gr. 0.8 for a depth of 2 m. Find 7. The diameters of a small piston and a large piston of a hydraulic jack are 2 cm and 10 cm respectively, A force of 60 N is applied on the small piston. Find the load lifted by the large piston, when: (a) the piston at the same level, and (b) small piston is 20 cm above the large piston. The density of the liquid in the jackis [Ans. (a) 1500 N, (b) 1520.5 NJ kg given as 1000 - 8. Determine the gauge and absolute pressure at a point which is 2.0 m below the free surface of water. Take [Ans. 1.962 N/cm? (gauge), 12.066 N/cm? (abs.)] - atmospheric pressure as 10.1043 N/cm?. 9. A simple manometer is used to measure the pressure of oil (sp. gr, = 0.8) flowing in a pipe line. Its right limb is open to the atmosphere and left…
Question is in figure
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]