A 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated load is at x = 14m (or the right end). Find the value of the maximum negative shear.

A 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated load is at x = 14m (or the right end). Find the value of the maximum negative shear.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. i) Reaction force at B in (N)= ii) Reaction Force at A in (N) = iii) The distance from B at which the shear Force value changes from "-" to "+" in (m) = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in (Nm) = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 2 cm from the top in (N/m^2) =
A rectangular beam 100 mm x 200 mm carries a uniformly distributed load of 5 kN/m over its simple span of 5 m. Compute for the maximum shear stress in the beam. Select the correct response: 0.94 MPa 0.38 MPa 0.66 MPa 0.56 MPa
For the cantilever bearn shown, determine the normal and shear stresses acting at point K. The cross-sectional dimensions of the beam cross section and the location of point K are also shown. Use the following values: a = 2.15 m, b = 0.80 m, Py 10 kN, P₂ = 8 kN, b = 165 mm, k = 59 mm, t = 12 mm, h = 42 mm, t = 6 mm, and d = 260 mm. by "
Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets. The property of the channel is given below: Depth, D = 225 mm Flange Thickness, t, = 9mm Flange Width, B; =112.5 mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t= 100 MPa on shear, for bearing, o,=200 MPa on single shear, o,-260MPA on double shear. 1. Determine the location of centroid, y, from top of the beam in mm. 2. Determine the moment of inertia, I, of the section in mm“. 3. Determine the maximum allowable moment, Mall, in kn-m, base on the beam's cross-section.
A beam simply supported on a 8 m span carries a uniformly distributed load of 30 kN/m over the middle 5 m. Using an allowable stress. fb = 120 MPa. A. Determine the most economical W shape beam, with the condition that the depth of the beam shoul not exceed 500 mm. B. What is the actual stress in the selected beam?
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
2. A uniformly distributed load of 54 Ib/ft is carried by a simply supported beam span. The beam is a hollow rectangular section, having a width, b = 10.5 inches, height, h = 11.2 inches and constant wall thickness of 0.9 inches. Determine the maximum length of the beam in feet if the shearing stress is limited to 82 psi. Assume the load acts over the entire length of the beam.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 14 cm as width, 23 cm as depth, and inner thickness as 1 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 7 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 2 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
A simply supported rectangular beam of length 5m has a width of 300mm and an effective depth of 500mm. The beam is to be reinforced using 12mm bars. The beam supports service dead loads of 25 kN/m and 30 kN/m, respectively. f'c= 28 MPa, fy= 420 MPa 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam. Expert Solution
Give correct answer and proper explanation
A 14-m simply supported overhang beam is supported at x = 0 and x = 10m. The overhanging portion is from x = 10m to x = 14m (the overhang portion is 4m). A uniform 20 kN/m load is from x = 0 to x = 5m and a 30 kN concentrated load is at x = 14m (or the right end). Find the value of the maximum positive moment.
A simply supported rectangular beam of length 6.45m has a width of 437.5 and an effective depth of 692.5. The beam is to be reinforced using 12 mm bars. The f'c is 28 and the fy is 420. The beam supports service dead loads of 31 kN/m and 39.5kN/m., respectively. 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam