A 1220-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. A 1960-N crate hangs from the far end of the beam. Using the data shown in the drawing find the following: What is the magnitude of the tension in the wire? Number N 50.0/ Вeam What is the magnitude of the horizontal component of the force that the wall exerts on the left end of the beam? 30.0° 1960 N Number N What is the magnitude of the vertical component of the force that the wall exerts on the left end of the beam? Number N

A 1220-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. A 1960-N crate hangs from the far end of the beam. Using the data shown in the drawing find the following: What is the magnitude of the tension in the wire? Number N 50.0/ Вeam What is the magnitude of the horizontal component of the force that the wall exerts on the left end of the beam? 30.0° 1960 N Number N What is the magnitude of the vertical component of the force that the wall exerts on the left end of the beam? Number N

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

You set up a Halloween prank by attaching a small board to a hinge above your front door. The far end of the board is held up by a cable that can be released by remote control. You place a spooky spider on the board that is dropped on unsuspecting trick-or-treaters when you release the cable. The drawing below shows the set-up. cable 40° Hinge 60 ст You use a board that is 60 cm long and the cable makes an angle of 40 degrees with the board when the board is held horizontally. You place the spider a distance of r = 37 cm from the hinge. The board has a mass of 2.2 kg and the spider has a mass of 1.6 kg. The hinge applies both a horizontal force and a vertical force. You will be asked to determine the direction of both of these forces (left, right, up, down). What is the magnitude of the tension in the cable in Newtons? T = What is the magnitude and direction of the horizontal force from the hinge? Enter a positive number for the magnitude. Fh = Direction ---Select--- What is the…
A 1140-N uniform beam is attached to a vertical wall at one end and is supported by a cable at the other end. A 1960-N crate hangs from the far end of the beam. Using the data shown in the figure, find (a) the magnitude of the tension in the wire and the magnitudes of the (b) horizontal and (c) vertical components of the force that the wall exerts on the left end of the beam. 50.0° 30.0% Beam 1960 N
Figure for Question # 18. Y 18. A uniform plank is supported by two equal 120-N forces at X and Y, as shown. The support at X is then moved to Z (half-way to the plank center). The supporting forces at Y and Z are then: * O A. F_Y=240 N, F_Z=120 N O B. F_Y=200 N, F_Z=40 N O C. F.Y=40 N, F_Z=200 N O D. F_Y=80 N, F_Z=160 N O E. F_Y=160 N, F_Z=80 N
A 800 N man is standing on a 4 m long plank of wood that is supported at each end by vertical ropes. The plank has a weight of 500 N and the man is standing 1 m from the left end. Find the force of tension in the rope at the left end of the plank.
A uniform beam of length L and mass mB is supported by two pillars located L/3 from either end, as shown in the figure. A duck of mass mD stands on one end. A scale is placed under each pillar. The entire system is in equilibrium. 1.) Enter an expression in terms of defined quantities and g, for the force under scale that the right pillar shows. 2.) Enter an expression in terms of defined quantities and g, for the force under scale that the Left pillar shows. 3.) Enter an expression in terms of defined quantities and g, for the sum of the scale readings.
Please answer clearly.
a. A 1200-N uniform boom of length 2.00 m is supported by a cable, as shown in the figure. The boom is pivoted at the bottom, and a 2000-N weight hands from its top. Find the tension in the cable and the components of the reaction force exerted on the boom by the floor. For the next two parts you can assume that the 2000-N weight is concentrated at the top end of the boom. b. Determine the total moment of inertia of the boom/weight system around the pivot point. c. The cable now breaks, and the boom pivots until the right end hits the floor. Determine the velocity of the right end at the instant before it hits the floor.
17 kg uniform store sign is held from a uniform horizontal beam as shown. There is a cable attached to the right edge of the beam and is secured to the wall, 250 cm above where the beam meets the wall. The sign is symmetrically suspended by two cords, the left cord being 80 cm from the wall, and the cord on the right being at the right edge of the beam, 200 cm from the wall. a. What is the tension in the left and right cords that hold the sign? b. What is the tension in the cable? c. What is the horizontal component of the force that the wall exerts on the beam?
A uniform beam with a length of 2.50 meters and a mass of 85.0 kg rests on two ropes. A person of mass 65.0 kg is standing on the far right end of the beam. The beam is not moving.Calculate the tension in the rope on the left, in Newtons (N).Calculate the tension in the rope on the right, in Newtons (N).
Q3. In the figure below, one end of the uniform beam of mass 50 kg is hinged to a wall. The other end of the beam is supported by a cable that makes angles e = 30 degrees with both the wall and the beam. A box of mass 10 kg is hanged at the end of the beam with a rope. The magnitude of the forces at the hinge. Hinge rope MB=10kg cable
Determine the forces in members BE and CE of the loaded truss. The forces are positive if in tension, negative if in compression. A 3.4 m 43° Answers: BE = CE= 2.9 m i 5.0 KN i B 5.6 KN E BC=CD 2.9 m KN KN 2
Three construction workers wish to remove a pole from the ground. They tie ropes to the pole and pull horizontally on the ropes. The diagram represents the forces exerted on the pole. 110 N 76 N 35° 40° 55 N Pole P a) Determine the direction (as measured with the x-axis) in which the pole will move. b) What must be the magnitude and direction of the equilibrant force needed to keep the pole in equilibrium?