ASAP PLA A 12-m high cylindrical tank to be filled with oil havingunit weight of 9.4 kN/m° will be built on site as shownin the figure.Oil12 my = 9.4 kN/m³GWT3.8 mSand: Ysat18.8 kN/m3Clay: Ysat = 17.6 kN/m³e.1.218 mLI = 0.65PL = 21%MС — 42%Determine the nearest value to the settlement of thetank.952 mm745 mm426 mm1015 mm

Answered: Image /qna-images/answer/728ea0ed-80ad-4d38-8789-483ad1cb50c4.jpg

A 12-m high cylindrical tank to be filled with oil having unit weight of 9.4 kN/m will be built on site as shown in the figure. Oil 12 m y = 9.4 kN/m³ GWT 3.8 m Sand: Ysat = 18.8 kN/m³ %3D Clay: Ysat = 17.6 kN/m3 eo = 1.2 18 m LI = 0.65 %3D PL = 21% MC = 42% Determine the nearest value to the settlement of the tank. 952 mm 745 mm 426 mm 1015 mm

A 12-m high cylindrical tank to be filled with oil having unit weight of 9.4 kN/m will be built on site as shown in the figure. Oil 12 m y = 9.4 kN/m³ GWT 3.8 m Sand: Ysat = 18.8 kN/m³ %3D Clay: Ysat = 17.6 kN/m3 eo = 1.2 18 m LI = 0.65 %3D PL = 21% MC = 42% Determine the nearest value to the settlement of the tank. 952 mm 745 mm 426 mm 1015 mm

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.1CTP

See similar textbooks

Similar questions

From the given figure. From the e-log p plot, two points were given. p1 = 80 kPa e1 = 0.60 p2 = 150 kPa e2 = 0.40 Determine the Liquid Limit.
CEN-333 Geotechnical
Water flows from Reservoir A to Reservoir B elevations: Elevation A = 120 ft and Elevation B = 100 ft. Flow is supported by a pump placed right after Reservoir A Pipe length = 12800 ft. Pipe diameter = 2ft, Hazen Williams Coefficient, C_HW = 100. Minor losses are accumulated using the following formula: hL minor = 0.001Q² [Q in feet ^3/s] Friction is computed: hL friction = K*Q1.85 where K is the pipe number = - Pump Characteristics are: Q[cfs] 0 10 20 25 30 35 H_p[ft] 300 273.0 225.5 187.5 138.0 79.5 a. Find Q in [cfs] b. (4.73* Pipe Length) (Pipe diamenter 4.87*C_HW1.85) Draw the EGL and HGL for the system. Be precise when drawing so your graphs represent relevant aspects of the system, and label points of change. Assume a friction factor f= 0.02; Kentry = 0.5, kexit 1.0 and that the pump is placed 100 ft down the line when measured from reservoir A, i.e, Axpump 100 ft = =
3. Determine the resultant of the three forces acting on the dam shown in the figure and locate its intersection with the base AB. Required: Resultant and its intersection with the base AB Solution: P-10,000 lb -24,000 f F-6000 tb
In an gas-oil system, the following fluid and sand data are available: h = 12.5 ft , hp = 5 ft Pw= 63.76 lb/ft , po= 47.5 lb/ft3 Bo = 1.1 bbl/STB , µo= 0.73 cp rw = 3 in , re = 1000 ft Ko= 93.5 md Calculate the oil critical rate. using Chaney method.
A well produces 850STBD amd1.67MMCF/STB the tubing diameter is4.5at a certain depth pressure is1002 psi calculated density for oil and gas is 805Kg/m^3 and 0.715kg/m^3 respectively Bo is 1.1 ,Bg=0.01ft^3/scf and Rs is 255 scf/stb calculated fluid slippage ,liquid hold up ,type of flow in the tubing and real phase velocities Using this equation to calculate it
Group B: 50-cm well penetrating a confined aquifer is pumped at a rate of a 0.035 m^3/s. The drawdown at an observation well at a radial distance of 100 m is as follows: Calculate the aquifer parameters S and T using Jacob method? T (hr) s(m) 3.5 4 0.3 0.5 1.5 2 3 7 10 30 70 90 100 170 200 250 0.08 0.10 0.25 0.30 0.34 0.37 0.41 0.50 0.55 0.75 0.88 0.93 0.95 1.04 1.08 1.13
AVA araupp g A p u s A pup upp n. 1. Answer the following questions about porosity and permeability: a) Name three (3) parameters which are involved in calculation of porosity. b) Name four geological mechanisms affecting porosity values. c) Describe effect of sorting on porosity. d) Describe how porosity and permeability are associated with one another. e) Permeability is seldom uniform throughout a reservoir. Thus, it is necessary to ascertain an average value of permeability, kavg. Elaborate with suitable diagrams two (2) examples of permeability averaging techniques. f) Two sandstone reservoir formations designated A and B are located 1 km apart. Their properties are given in Table Q1(f). Outline FOUR (4) reasons for which reservoir B is commercially more viable than reservoir A.
Civil engineering -Hydraulics
The bottom diameter of a dug well in fine sand region to obtain 10 e/s of yield under a depression head of 2.5 m. The value of specific capacity per unit area may be taken as 0.6 h-¹ is
The following data relate to a pump-out test: Diameter of well = 24 cm; Thickness of confined aquifer = 27 m; Radius of circle of influence = 333 m; Draw down during the test = 4.5 m; Discharge = 0.9 m^3/s.What is the permeability of the aquifer in mm/s? Choices: a. 2.15 x 10^-2 b. 4.5 x 10^-1 c. 93 X 10^-1 d. 1.6 X 10^-1
Estimate the Q that produced a drawdown in a 1 ft diameter well of 5 feet above the bottom of a pressurized aquifer with a 35 ft thickness and a head in a monitoring well 55 ft away 25 ft above the bottom of the aquifer in a clean course sand aquifer with K ~ 3*10^(-3) ft/sec.