A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N. The value of the axial force in thestrong bar in N....10 m200N10ÖNLB10 m

Answered: Image /qna-images/answer/ca56ced6-4540-4cc4-945b-2e2f8653499c.jpg

Answered: A 100N load is supported by a strong…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 Consider the pipe segment AB that lies in the az-plane and is bent in a circular form with radius 4 m. The pipe is supported at A by an unknown support and at B with a cable BC. B' A50 4 m If the support at A can resist a maximum cou- ple moment of 1 650 Nm, determine the small- est force F that will cause the support to fail. F 6 m D 6 m
Question 4(a) The uniform bar shown in Figure 4 weighs 428 N. It is supported by a pin at A and a cable that runs around the pulley, D. It is subjected to a uniformly distributed load of 17.7 N/m and 12.5 Nm clockwise moment at E. Beam is in equilibrium position as shown in the Figure. Take a = 0.41 m and b = 2.5 m. Determine the tension in the cable and the reaction force at A, both in Newtons. w N/m 75° A ▼▼ ▼ ▼ 12.5 Nm B E 1 m 0.5 m m b Figure 4 Question 4(b) Find a truss from your neighborhood where you can take a photo safely. It does not have to be taken from the perfect angle and as long as we can see the complete truss that is good enough. One photo would be ideal but upto 3 photos can be used. Include these photos in your solutions for this question and based on these photos draw this 2D truss (exact dimensions are not required) with the supports too. Comment on the possible loads and their locations that may be applied to the truss. Discuss the assumptions that you have to…
Determine the maximum shear stress and angle of twist (in degrees) of one tip with respect to other. The material of the component has a modulus of rigidity of 24 GPa. positive applied moments are CW when seen from E to A. Moment at A= 400 N.m Moment at B = -600 N.m Moment at C= 300 N.m Moment at D = 500 N.m Moment at E= -600 N.m L is 0.25m and Radius of the rod is 30mm
A. Calculate the shear force in the pin at B in pounds. B. Calculate the shear stress in the pin at B in psi.
the 2nd pic is the answer key
5. For the plane truss presented in Figure, calculate the reactions at the two supports under the applied load. 251 25t d b und 4m 50t 6t 3m 4m
Draw the shear force diagram and the bending moment diagram of the bridge girder shown below. FAC = 84.1K (T) Fec 84.1K (T) FCD=64.7 K (c) 5 ft A 12 ft- 80 k D C 12 ft B
Need asap
The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point C to point A. (Figure 1) Figure K 1 of 1 > 0.15 m 0.4 m 0.2 m 03m 05 m 0.25 m 0.2 m
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm². The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. D 1.7m 1.7m -P B 3.5m7 Find the location x of the largest additional vertical force that can be applied to the bar. meters in 2 decimal places
Gate AB retains water as shown in the figure. The gate is supported every 2 m (perpendicular to the plane of view) by member BC, which is attached to a 2000 kg mass at point C. What minimum static coefficient of friction μs, along the contact surface between the mass and its base, is needed for the gatestructure to be in equilibrium? There are pins at points A, B, andC.
Solve the problem using influence lines. Determine the maximum force (tension or compression) at member IH of a two-side bridge truss due to a series of concentrated load shown. Assume the loads can travel in either direction along the center of the deck, so that half its load is transferred to each of the two trusses Given: T= 2.16 U= 8.64 V= 13.5 W= 8.1 X= 10.8 Y= 5.4

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N. The value of the axial force in the strong bar in N.