A 100 kVA, 230V load operates at 0.80 lagging power factor. The power factor is to be improved to 0.80 leading by a capacitor bank. However, the capacitors are loosely connected and take 50 kW when connected to a 230V, 60Hz AC source. a. What is the total KVA consumption when the capacitor bank is connected? (162.5 kVA) b. What is the kVAR rating of the capacitor bank? (157.5 kVAR) c. Find the capacitance of the capacitor. (7.8976 mF)

Q: A voltage and current applied to a single phase load is v= 195 sin (300t+35°) and i= 175 sin (250t-…

A: Since frequency are different so  Net real power will be zero in single and 3 phase system.

Q: The drawing shows three ac circuits, as shown below, each connected to identical generators.…

A:

Q: A given load takes 40 kVA at 50% lagging power factor, while another load is connected in parallel…

A: Given: A load takes 40 kVA at 50% lagging power factor. Other load takes 80 kVA 86.7% lagging power…

Q: In a system of 132 kV, the circuit phase to ground capacitance is 0.2 uF and the circuit inductance…

A:

Q: 11 kV at a power factor of 0.867lagging. Each machine supplies half the total power. The synchronous…

A:

Q: sformer 1200 KVA, 11000/2200 V, 50 Hz e reactance/phase of the primary winding ar ding values for…

A:

Q: A single phase AC motor draws 4.5 A from the 220 V, 50 Hz network. The active power drawn by the…

A: 1-ϕ AC motor draws current=4.5AI=4.5AV=220VP=720WSolving by the formula-P=VIcosϕPutting the values…

Q: Problem: Sketch the dotted equivalent circuit for the coupled coils shown in figure and find the…

A: SOLUTION !!

Q: 200/0°V L In the circuit in the figure; • Ly load draws 15 kVA with lagging power factor 0.6. • The…

A:

Q: Three phase power supply load R is 1699 VA, S is 15584 VA and T is 12818 VA. Find (a) the…

A:

Q: Determine the rms current I as shown in figure 1. Source voltage is eady in RMS value (Answer must…

A:

Q: Determine the apparent power, active power and reactive power in a series circuit, when the supply…

A:

Q: The open circuit characteristics (O.C.C) of an alternator is drawn between O Eo V/S Ir O E, V/S Isc…

A: To find open circuit characteristics, the Terminal voltage of the alternator is open-circuited or…

Q: There are two loads connected in parallel and powered from a 7200-V source. The first load is 50-kVA…

A:

Q: In the Synchronous machine phasor representing Blondels two reaction theory, which of the following…

A: Question:  In the Synchronous machine phasor representing Blondels two reaction theory, which of the…

Q: 45. A 3-phase, 5 kW induction motor has a p.f. of 0.75 lagging. A bank of capacitors is connected in…

A: Given: A 3-phase, 5 kW induction motor has, Power factor, cosϕ1=0.75 lagging…

Q: A lagging system with a complex load has a power factor of 0.75 and an applied voltage of 200V. if…

A: Given data, A lagging system has, Power factor cosϕ=0.75. Voltage, VL=200 V. Apparent power, S=10…

Q: During fast decoupled Method load flow analysis in one of the loads the calculated reactive power…

A: The power system analysis has non linear equations of power. The equations are  involving voltage…

Q: A capacitor of capacitance 120 uF is connected across a 220 V, 60 Hz A.C. mains. Calculate the…

A:

Q: Question 6 Vs 20020°V L L S. rms In the circuit in the figure; Lload draws 15 kVA with lagging power…

A:

Q: Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period…

A:

Q: A voltage and current applied to a single phase load is v= 26 cos (300t+25°) and i= 12 cos (250t-…

A: If a voltage v=v1 cos(wt -α) and current i=i1 cos(wt-β) flow through any load then the total active…

Q: 32) Bypass diodes are MOST often located in which PV system component? O Ihverters O Modules O…

A:

Q: There phase power supply load R is 1699 VA, S is 15584 VA and T is 12818 VA. Find (a) the…

A:

Q: Distinguish the different kinds of quantities and description of power in alternating current…

A:

Q: The frequency of a sinusoidal alternating current is 65 Hz and its maximum value is 12 A. The…

A: sinusoidal alternating current Frequency f=65 Hz maximum value Im 12 A. The current starts at zero…

Q: The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical…

A: Given: Load-1:P1=950Wcosϕ1=0.5 LaggingLoad-2:P2=1.14Wcosϕ2=1Load-3:P3=760Wcosϕ3=0.5 leadingline…

Q: 7. What capacitance has a reactance of 802 when a 500HZ source is connected?

A: capacitive reactance Xc = 12πfC Where f is the frequency  and c is capacitance .

Q: A voltage and current applied to a single phase load is  v= 26 cos (300t+35)  and i= 19 cos (250t-…

A: Given: v=25cos300t+35°i=19cos250t-20°

Q: For the following voltage and current waveforms, the length of the current waveform parts are equal.…

A:

Q: - The Voll-age V: 100210°V is applied V= l00210v is applied across a capacilive 1oad . The Load 1-a…

A: The given data is: Voltage, V=100∠10°V,Apparent Power,S=500VA,Power Factor,pf=0.8 leading

Q: The total impedance in the polar form in ohm. The total current in polar form. The total power…

A:

Q: 4+ 1j O A I, = 20/10° Awgk/rms* []3 + 45 i. 3- j4 2 ii. 3+ j4 2 iii. 5.00 2 iv. 8.60 2 v. 4+ jl N…

A:

Q: The voltmeters in the figure measure RMS voltages. If V1 = 13 V and V2 = 3.5V what is V3? R L VI V2

A:

Q: Average active power in a Three Phase Circuit= W Select one:

A: Active power in a 3 phase circuit can be calculated by two method either by line current line…

Q: An electrodynamometer type wattmeter is used to measure power in 1-o circuit. The connected load…

A: The solution is given below

Q: 2. Three series loads are drawing 20A ms current through a 60Hz source. Load 1 is an 400W, 0.8…

A: We are authorized to answer three subparts at a time since you have not mentioned which part you are…

Q: A Load absorbs 10 kVA at a lagging power factor of 0.6. The complex power is: Select one: a. 2000+…

A: The correct solution is given below

Q: If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a.…

A:

Q: Discuss how diode limiters and diode clampers differ in terms of their function

A: In this question we will write  difference between clipper and clamper circuit...

Q: 6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer…

A: In this question,  We need to calculate the current I in the rms.  We are solving this problem using…