A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute delivers water at a temperature of 150 F. If the slip is 7%, determine the a. discharge in lb/hr b. discharge in gpm

A 10-in. x 6-in. x 12-in. duplex direct-acting steam pump operating at 35 strokes per minute delivers water at a temperature of 150 F. If the slip is 7%, determine the a. discharge in lb/hr b. discharge in gpm

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter8: Leak Detection, System Evacuation, And System Cleanup

Section: Chapter Questions

Problem 2RQ: Name and briefly describe the six classes of leaks.

See similar textbooks

Related questions

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then, Select one:…

A: ANSWER = (a) cavitation will formed.

Q: The manufacture has identified the displacement of this pump as 1.25 cubic inches per ev. The prime…

Q: A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point…

Q: Drive an equation describes the volumetric flow rate in triangular open conduit.

Q: A regenerative circuit uses a cylinder with a 3 inch bore and a 1.84 inch rod. A pump is providing 8…

A: Given: Bore diameter, D = 3 in Rod diameter, d = 1.84 in Flow rate, Q = 8 gal/min or 30.8 in3/s…

Q: operating at a speed of 880 rpm can supply water at a rate of 7000 gpm. The maximum head that this…

A: Maximum head = 18.78 feet = 19 feet (whole number)

Q: A centrifugal pump driven by a 160-hp motor rotating at 2400 rpm is used to pump 70°F water in a…

Q: 8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter…

A: given data; ⇒flow rate (Q)=10gpm=6.309*10-5m3/s⇒piston diamter (d1)=7 in=0.1778m⇒rod diamter(d2)=5…

Q: Show in Figure 1 is the water flow system. The velocity head difference is v²₁-v²₂. -= 2.0m. Volume…

A: Given data V12-V222g=2m Q=0.5m3/s h1=1m…

Q: How is the capability of a variable displacement pump changed by the addition of pressure…

A: A pressure compensating pump will deliver its maximum flow until the system pressure reaches the…

Q: 10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler…

A: Apply the relation of the polytropic index.

Q: A flexible tube peristaltic pump operates at 100 rpm, with a lobe volume of approximately 3 ml. What…

Q: 6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge…

Q: Discuss the relation between the head pressure and flow rate for the benefits of connecting the…

A: Solution:

Q: B- A three-lobe rotary positive-displacement pump moves 0.45 cm³ of blood in each lobe volume Vlobe.…

Q: Q2- Water ( p= 990 kg/m' & u= 0.001 pa.s) is pumping from a water tank to water injection well with…

Q: A cylinder with a bore of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system…

Q: If the velocity of water is 8 m/s and the pressure is 140 kPa on the discharge side of a pump. a.…

Q: If the net positive suction head (NPSH) requirement for the pump is not satisfied, then_ Select one:…

A: NPSH is the property of the pump and it is defined as the difference between the available NPSH at…

Q: Determine the size of the diesel engine to be used for a 4 inches X pump. Pump discharge is 200gpm.…

Q: A pump is moving soybean oil through a 1-in. (nominal) pipe. The 110-volt motor is using 285 watts.…

A: Given dataDiameter of pipe = 1 inch = 0.0254 mVoltage of motor = 110 VPower of motor = 285 WOverall…

Q: Figure 8.12 shows a portion of a fire protection system in which a pump draws water at 60°F from a…

Q: 4. At a proposed hydroelectric power plant site, the tailwater elevation is 470m. The estimated…

Q: estimate the volume flow rate of water through the siphon

A: Given data: Apply Bernoulli’s equation between the free surface of the tank and the exit of the…

Q: B/ Find the flow rate in units of L/s that an axial piston pump delivers at 1000 rpm. The pump has…

Q: In centrifugal pump if we know the value of actual discharge is 250 l/sec , then find the value of…

A: Given, Actual discharge, Q=250L/s To calculate :- head(H) Now we know that Q=AvQ=Cd π4d2 vv=2gHand…

Q: Provide the diagram for the problem. Choose the correct answer and provide complete solution.…

A: given; height(h1)=500ft =152.4mheight(h2)=250ft…

Q: B- A three-lobe rotary positive-displacement pump moves 0.45 cm³ of blood in each lobe volume Vlobe-…

Q: What is performance characteristics of a centrifugal pump

A: A centrifugal pump is designed to develop certain manometric head and discharge at constant speed…

Q: A multi-stage centrifugal pump discharges 1200 gpm of water at 1400 rpm with pressure head of 1200…

Q: A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when…

A: To Find : The power delivered by the pump to water . Given : The water flow rate is : Q=250…

Q: Water at 5°C is to be pumped from the river to the bottom of a water tower. The pump is 5 m above…

A: Given: a=5 mDa=6 inb=19.5 mDb=4 inc=4.2 mFlow rate (Q)=0.021 m3/sHead losses are:hL,a=1.2 mhL,b=4.2…

Q: A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total…

A: Given data : Friction factor (f)=0.023 Discharge (Q)=0.15 m3/s Length (L)=150 m Diameter (d)=200 mm…

Q: A water pump develops a total head of 200 feet. The pump efficiency is 80% and the motor efficiency…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylinder with a bore of 4.5 inches and a rod diameter of 1.5 inches is to be used in a system with a 6 GPM pump. What is the extension speed of the cylinder?
8. In the regenerative circuit shown below, the pump's flow rate is 10 gpm. If the piston diameter is 7 in and the rod diameter is 5 in (not a 2:1 cylinder), calculate the extension speed in in/min. Also calculate the oil flow rate at points A and B in gpm. (recall 1 gal = 231 in') PF The diagram above does not show a working regenerative circuit. What must be added in order for the circuit to be practical and why?
1. A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the brake horsepower? a. 1.43 hp b. 2.04 hp c. 2.41 hp d. 2.67 hp 2.A LEV system has a centrifugal fan rotating at 714 rpm. The airflow is 6210 cfm, the fan total pressure is 4.07” w.g., and the brake horsepower is 3.12 hp. If the rotating speed is decreased to 620 rpm, what are the new value for fan total pressure? 4.15" w.g. 3.87" w.g. 3.07" w.g. 3.94" w.g.
QUESTION 3 A submersible deep-well pump delivers 250L/min of water through a 1-in Schedule 40 pipe when operating in the system sketched in Fig. 3. An energy loss of 2.3 m occurs in the piping system. (a) Calculate the power delivered by the pump to the water. (b) If the pump draws 1 hp, calculate its efficiency. A 27 kba 12 m
8.) A liquid having a sp.gr. of 20 is flowing in a 50 mm diameter pipe. The total head at a given point was found to be 17.5 Joule per Newton. The elevation of the pipe above the datum is 3 m and the pressure in the pipe is 65.6 kPa. Compute the velocity of flow and the horsepower in the stream at that point. Subject: Fluid Mechanic Lesson: Relative Equilibrium of Liquids Fundamentals of Fluid Flow
Number 2 question Complete solution and correct units pls. Draw the figures if necessary
Topics: Fundamental of fluid flow Oil (SG=0.82) entering a pump through an 8-inch diameter pipe at 4 psi has a flow rate of 3.5 cfs. It leaves the pump through a 4-inch diameter pipe at 15 psi. Assuming that the suction and discharge sides of the pump are at the same elevation, find the horsepower delivered to the water by the pump (550 lb.ft/s = 1 HP). Illustrate the problem and show your complete solution.
Q/ Discuss the relation between the head pressure and flow rate for the benefits of connecting the pumps in series?
Need in rush!
6. A pump draws water from a sump through a vertical 6" pipe. The pump has a horizontal discharge pipe 4" in diameter that is 10.6 ft above the water level in the sump. While pumping 1.25 cfs, gages near the pump at entrance and discharge read -4.6 psi and +25.6 psi, respectively. The discharge gage is 3.0 ft above the suction gage. Compute the horsepower output of the pump and the head lost in the 6" suction pipe.
A regenerative circuit uses a cylinder with a 3 inch bore and a 1.84 inch rod. A pump is providing 8 gal/min of flow. What is the extension speed (in in/sec) of this cylinder?
10 m3/min of free air is to be compressed to 8 bar gauge in two stages. Assuming an intercooler pressure of 2 bar gauge and polytropic index of 1.3, what will be the flowrate at the exit of the intercooler ?Please choose correct option.a.4.295 m3/minb.312 litre/sec.c.3333 litre/mind.1172 litre/min.e.981 m3/min